Publicité
Les langues disponibles
Les langues disponibles
Anleitung_NMC_355_SPK7:_
GB
30. In the case of cutting-off wheels with straight-
sided flanges, be sure to observe the
recommend values for thickness and hole
diameter.
Wear safety goggles
Wear ear-muffs
Wear a breathing mask
Noise emission values
Sound pressure level, LPA
Sound power level, LWA
5. Technical data
AC motor
Power P
Idle speed n
0
Cutting-off wheel
Ø 355 x Ø 25.4 x 3.2 mm
Footprint
Swiveling range
Vise clamping range max.
Saw width at 90°
Saw width at 45°
Weight
6. Before putting the machine into
operation
Unpack the metal cutting-off machine and check
it for damage which may have occurred in
transit.
The machine has to be set up where it can stand
firmly, e.g. on a work bench, or it must be bolted
to a strong base.
All covers and safety devices have to be pro-
perly fitted before the machine is switched on.
It must be possible for the cutting-off wheel to
run freely.
Before you actuate the ON/OFF switch, make
sure that the cutting-off wheel is correctly fitted
and that the machineʼs moving parts run
14
24.09.2008
9:47 Uhr
Seite 14
smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
7. Assembly
Caution! Pull out the power plug before carrying
out any maintenance, resetting or assembly work
on the cutting-off machine!
7.1 Transport brace / carry-handle (Fig. 1 / 2)
The saw head (1) is anchored in its lower
position with a chain (13). (Fig. 2)
Push down the saw head (1) by the handle (2)
and unhook the chain (13).
Slowly raise the saw head (1).
Caution! The resetting spring lifts the saw head
(1) automatically. Therefore, do not simply let go
98 dB (A)
of the handle (2) after cutting, but allow the saw
111 dB (A)
head (1) to rise slowly by applying slight
counterpressure.
Fig.1 shows the saw head (1) in its upper
position.
Whenever you want to transport the machine
you should use the chain (13) to anchor the saw
230 V ~ 50 Hz
head (1) again in its lower position.
2000 watts
The saw is equipped with a carry-handle (8) to
3900 min
-1
make it easier to transport.
445 x 245 mm
7.2. Vise (Fig. 3 / 4)
0 - 45°
Every workpiece has to be fastened in the vise (15)
before it is cut.
0 - 240 mm
Flip up the top half of the nut (14).
Ø 100 / 70 x 170 mm
Pull out the spindle (5) far enough for the work-
100 x 70 mm
piece to be clamped between the clamping faces
19.6 kg
(4/7) of the vise (15).
Note: You do not have to turn the spindle (5)
when the top half of the nut (14) has been
flipped up. The spindle (5) can be pulled out or
pushed in to the exact amount required.
Push forward the spindle (5) to the point where
the clamping face (4) touches the workpiece.
Flip down the top half of the nut (14) again so
that the spindle (5) and both halves of the nut
engage with each other.
Turn the hand crank (6) to safely secure the
workpiece in the vise (15).
7.3. Miter cuts (Fig. 5)
The vise can be swiveled from 0° to 45° in order to
make miter cuts.
Slacken the two screws (16/17).
Turn the clamping face (7) of the vise (15) to the
required angle.
Publicité
