Additional Safety Warnings - Scheppach CAG115-20ProS Traduction Des Instructions D'origine

Additional safety warnings specific for abrasive
cutting-off operations:
a) Do not "jam" the cut-off wheel or apply ex-
cessive pressure. Do not attempt to make an
excessive depth of cut. Overstressing the wheel
increases the loading and susceptibility to twisting
or binding of the wheel in the cut and the possibil-
ity of kickback or wheel breakage.
b) Do not position your body in line with and be-
hind the rotating wheel. When the wheel, at the
point of operation, is moving away from your body,
the possible kickback may propel the spinning
wheel and the power tool directly at you.
c) When wheel is binding or when interrupting a
cut for any reason, switch off the power tool
and hold the power tool motionless until the
wheel comes to a complete stop. Never at-
tempt to remove the cut-off wheel from the cut
while the wheel is in motion otherwise kick-
back may occur. Investigate and take corrective
action to eliminate the cause of wheel binding.
d) Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully re-enter the cut. The wheel may bind,
walk up or kickback if the power tool is restarted
in the workpiece.
e) Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kick-
back. Large workpieces tend to sag under
their own weight. Supports must be placed un-
der the workpiece near the line of cut and near the
edge of the workpiece on both sides of the wheel.
f) Use extra caution when making a "pocket
cut" into existing walls or other blind areas.
The protruding wheel may cut gas or water pipes,
electrical wiring or objects that can cause kick-
back.
g) Do not make curved cuts. Overstressing the
wheel increases the loading and susceptibility to
twisting and binding of the wheel in the cut and
the possibility of kickback or wheel breakage,
which can lead to serious injuries.

6. Additional Safety Warnings

1. When using depressed centre grinding wheels,
be sure to use only fiberglass-reinforced wheels.
2. Never use Stone Cup type wheels with this grind-
er. This grinder is not designed for these types of
wheels and the use of such a product may result
in serious personal injury.
3. Be careful not to damage the spindle, the flange
(especially the installing surface) or the lock nut.
Damage to these parts could result in wheel
breakage.
4. Make sure the wheel is not contacting the work-
piece before the switch is turned on.
24 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
5. Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate poor installation or a poorly
balanced wheel.
6. Use the specified surface of the wheel to perform
the grinding.
7. Do not leave the tool running. Operate the tool
only when hand-held.
8. Do not touch the workpiece immediately after op-
eration; it may be extremely hot and could burn
your skin.
9. Observe the instructions of the manufacturer for
correct mounting and use of wheels. Handle and
store wheels with care.
10. Do not use separate reducing bushings or adap-
tors to adapt large hole abrasive wheels.
11. Use only flanges specified for this tool.
12. For tools intended to be fitted with threaded hole
wheel, ensure that the thread in the wheel is long
enough to accept the spindle length.
13. Check that the workpiece is properly supported.
14. Pay attention that the wheel continues to rotate
after the tool is switched off.
15. If working place is extremely hot and humid, or
badly polluted by conductive dust, use a shortcir-
cuit breaker (30 mA) to assure operator safety.
16. Do not use the tool on any materials containing
asbestos.
17. When use cut-off wheel, always work with the
dust collecting wheel guard required by domestic
regulation.
18. Cutting wheels must not be subjected to any lat-
eral pressure.
m WARNING
This electric tool generates an electromagnetic
field during operation. This field can impair ac-
tive or passive medical implants under certain
conditions. In order to prevent the risk of serious
or deadly injuries, we recommend that persons
with medical implants consult with their physi-
cian and the manufacturer of the medical implant
prior to operating the electric tool.
Information on the rechargeable battery
Please observe the operating manual for the re-
chargeable batteries.
Information on the charging unit and charging
process
Please observe the operating manual for the charg-
ing unit.