Nordcap S125E Pizza Serie Manuel D'instructions page 28

WARNING!
Before re-positioning the right side panel, using a
compass wrench reload the spring until the tension of the door when
opening and closing is deemed satisfactory.
5.3.6 REPLACING THE HANDLE SPRING
After carrying out the operations described in 5.1 above, to replace the
handle spring proceed as follows:
- remove the left side panel (item 5, plate A) by unfastening the four
fixing screws;
- disconnect the spring (item 21 plate A) by unscrewing the two fixing
nuts;
- replace the spring, using the two nuts to set the correct tension;
- perform the above operations in reverse order to reassemble the panel.
5.3.7 REPLACING THE
EMBOSSED SHEET STEEL DECK
After carrying out the operations described in 5.1 above, to replace the
floor proceed as follows:
- Open the front door ;
- Lift the floor (item 4 or 39 plate A) using a screwdriver as a lever.
- Replace the floor.
5.3.8 REPLACING THE SAFETY THERMOSTAT
WARNING!
Regularly check that the safety thermostat is
operating correctly.
After carrying out the operations described in 5.1 above, to replace the
safety thermostat proceed as follows:
- take off the right side panel (item 6, Plate A) by unfastening the four
fixing screws;
- disconnect the thermostat faston connectors;
. take off the right side panel by unfastening the four fixing screws;
- remove the thermostat sensor, located inside the insulating rock wool,
using a blade to remove the section of rock wool involved;
- replace the thermostat (item 28, plate A) and the respective sensor,
along with any worn rock wool insulation, if necessary;
- perform the above operations in reverse order to reassemble.
5.3.9 HEATING ELEMENT REPLACEMENT
(Only S100E/I – S105E/I – S120E/I – S125E/I)
After carrying out the operations in point 5.1, to replace the elements,
proceed as follows:
- remove the right side panel (item 6 tab.A) loosen the four fastening
screws;
- disconnect the power cables from the element to be replaced;
- use a blade to remove the rock wool section concerned;
- loosen the two fastening screws;
- replace the heating element;
- carry out the above steps in reverse order to refit the parts, replacing
the rock wool section previously removed, if necessary.
NOTE:
Only when replacing the first heating element in the
bottom front, is it necessary to remove the refractory panels (5.3.7)
and remove the relevant shims under the surface.
5.4 REPLACING PARTS
COMPARTMENT
5.4.1 REPLACING THE LIGHT BULB
After carrying out the operations described in 5.1 above, to replace the
light bulb and/or cover, proceed as follows from the inside of the
leavening compartment:
- unscrew the cover (item 7, plate B) and replace the bulb (item 4, plate
B) and/or the cover itself.
- replace the cover.
5.4.2 REPLACING THE THERMOSTAT
After carrying out the operations described in 5.1 above, to replace the
thermostat proceed as follows:
- remove the casing for access to parts from the inside;
- disconnect the thermostat faston connectors;
- remove the thermostat dial (item 2 plate B);
- unfasten the fixing screws of the heating element support;
- remove the thermostat sensor located inside the compartment;
- replace the thermostat (item 3 plate B) and the respective sensor;
- perform the above operations in reverse order to reassemble.
5.4.3 REPLACING THE MAGNETIC DOOR FASTENER
After carrying out the operations described in 5.1 above, to replace the
magnetic door fastener proceed as follows:
REFRACTORY FLOOR
OF THE LEAVENING
- open the doors of the leavening compartment (plate B);
- remove the seal snap ring (plate B);
- replace the magnetic door fastener (item 13 plate B).
5.4.4 THERMOSTAT DIAL REPLACEMENT
After carrying out the operations described in 5.1 above, to replace the
thermostat dial and/or relative ring nut, proceed as follows from the
outside of the compartment:
- remove the snap-on thermostat dial (item 2, plate B);
- replace the dial.
5.4.5 INDICATOR LIGHT REPLACEMENT
After carrying out the operations described in 5.1 above, to replace the
indicator light and the light switch proceed as follows:
- remove the casing for access to parts from the inside;
OR
- disconnect the indicator light faston connectors;
- replace the indicator light (item 1, plate B);
- perform the above operations in reverse order to reassemble.
5.4.6 REPLACING THE HEATING ELEMENTS
After carrying out the operations described in 5.1 above, to replace the
heating elements proceed as follows:
- remove the protective casing from the heating elements;
- loosen the heating element fastening screws;
- disconnect the heating element supply wires;
- remove the heating elements (item 6, plate B);
- perform the above operations in reverse order to reassemble.
5.5 REPLACING
COMPARTMENT WITH HUMIDIFIER
5.5.1 REPLACING THE TRAY HEATING ELEMENT
After carrying out the operations described in 5.1 above, to replace the
tray heating element proceed as follows:
- loosen the fastening devices;
- remove the protective casing from the tray;
- loosen the screws fastening the heating element;
- remove the heating element (item 14 tab.B);
- disconnect the power wires from the heating element;
- perform the steps in reverse order to refit the new heating element.
5.5.2 REPLACING THE INDICATOR LIGHT AND THE
HUMIDIFIER SWITCH
After carrying out the operations described in 5.1 above, to replace the
humidifier switch proceed as follows:
- remove the casing for access to parts from the inside;
- disconnect the faston connectors for the humidifier switch.
- Replace the humidifier switch (item 16 plate B).
- Perform the above operations in reverse order to reassemble.
5.6 DISPOSAL
When the oven or its spare parts are dismantled, the various components
must be sorted by type of material and disposed of in compliance with
current local laws and regulations.
UK/13
PARTS OF THE
The presence of a wheeled dustbin with a line through
it indicates that within the European Union electrical
components are subject to special collection at the end
of their working life. As well as to this device, the
standard applies to all of its accessories if marked with
this symbol. Do not dispose of this product as normal
urban waste.
LEAVENING