Bosch EXACT ION 6-1500 WK Notice Originale page 16

16 | English
made breathing apparatus that can filter out even the smal-
lest of dust particles) and work only in well-ventilated areas.
Avoid switching on the tool accidentally. Make sure
u
that the on/off switch is set to the off position before
inserting a battery. Accidents can occur as a result of
carrying the power tool with your finger on the on/off
switch or inserting the battery while the power tool is
switched on.
Do not use application tools that are worn or in other-
u
wise less than perfect condition. Defective application
tools can break, for example, causing material damage
and personal injury.
When fitting an application tool, make sure that it is
u
held securely in the tool holder. If the application tool is
not held securely in the tool holder, it may become loose
and consequently uncontrollable.
Be careful when screwing in long screws – there is a
u
risk of slipping when using particular screws and ap-
plication tools. Long screws are often difficult to control
and there is a danger that you will slip and hurt yourself
when screwing them in.
Check which rotational direction is set before switch-
u
ing on the power tool. If you want to loosen a screw but
the rotational direction is set to tighten the screw, for ex-
ample, the power tool may move violently and uncontrol-
lably.
Do not use the power tool as a drill. Power tools with a
u
shut-off clutch are not suitable for drilling. The clutch can
shut off automatically and without warning.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for tightening and loosening
screws, bolts, nuts and other threaded connectors in the
specified power and dimension ranges.
Technical data
Industrial cordless angle wrench EXACT
ION
Article number
Rated voltage
Torque, hard/soft screwdriving application
A)
according to ISO 5393
A)
No-load speed n
0
Weight according to EPTA-Procedure
A)
01:2014
1 609 92A 4R2 | (21.02.2019)
The power tool is suitable only for use in industrial environ-
ments.
The power tool is not suitable for use as a drill.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Application tool
(2) Tool holder
(3) Angled screw head
(4) Spanner flat on the angled head flange
(5) Spanner flat on the cap nut
(6) Worklight
(7) Slider for preselecting the torque
(8) On/off switch
(9) Rotational direction switch
(10) Battery charge indicator
(11) LED indicator for screwdriving applications
A)
(12) Battery
(13) Battery release button
(14) Handle (insulated gripping surface)
(15) Hanging hook
(16) Attachment slots for hanging hook
(17) LED holder
(18) Marking ring
(19) Spring ring
(20) Cavity in the housing shell
(21) Open-ended spanner (27 mm width across flats)
(22) Open-ended spanner (22 mm width across flats)
(23) Quick-change chuck
(24) Adjustment tool
A)
(25) Hex key
(26) Setting disc
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
6-1500 WK 8-1100 WK
3 602 D94 406 3 602 D94 407 3 602 D94 408 3 602 D94 409
V= 18
Nm 2 – 8
-1
min 105 – 1050 110 – 750
kg 1.5 – 2.7 1.5 – 2.7
A)
A)
A)
A)
A)
A)
12-700 WK 12-450 WK
18 18
2 – 11 2 – 16
70 – 500
1.5 – 2.7
Bosch Power Tools
A)
A)
18
2 – 16
45 – 320
1.5 – 2.7