LEGRAND Wattstopper FSP-201B Instructions D'installation page 3

Ground
(Green)
Non-Dimming
Ballast/Driver
CTRL (Blue)
Dim– (Gray)
Dim+ (Violet)
+VDC (Red)
Ground (Green)
Dim-to-Off
Ballast/Driver
Dim– (Gray)
(Blue)
+VDC Output (Red)
COM/GND (Black)
Dim+ (Violet)
The FSIR-100 operates on three standard 1.5V AAA Alkaline batteries or three rechargeable AAA NiMH
batteries. The battery status displays in the upper right corner of the display. Three bars next to BAT=
indicates a full battery charge. A warning appears on the display when the battery level falls below a
minimum acceptable level. To conserve battery power, the FSIR-100 automatically shuts off 10 minutes
after the last key press.
• If communication is not successful, (if possible) move closer to the sensor.
• If still not successful, there may be too much IR interference from other sources. Programming the unit
at night when there is no daylight available may be the only way to communicate with the sensor.
Navigate from one field to another using (up) or (down) arrow keys. The active field is indicated by
flashing (alternates) between yellow text on black background and black text on yellow background.
Once active, use the Select button to move to a menu or function within the active field. Value
fields are used to adjust parameter settings. They are shown in "less-than/greater-than" symbols:
<value>. Once active, change them using(left) and(right) arrow keys. The right key increments and
the left key decrements a value. Selections wrap-around if you continue to press the key beyond
maximum or minimum values. Moving away from the value field overwrites the original value. The
Home button takes you to the main menu. The Back button can be thought of as an undo function.
It takes you back one screen. Changes that were in process prior to pressing the key are lost.
NOTE: When you change parameter values on the FSP-201B, you need wait about 3 minutes
before the new parameters are saved into the memory.
Neutral
(White)
Line (Black)
BZ-200 Power Pack
120 – 277 VAC (1 φ ), 50/60 Hz
20A Ballast/ELV/MLV/Tungsten/LED LISTED
16A E-Ballast/CFL
Appliance
Control
1HP @ 120/240VAC
88T9
20A 120VAC Plug Load – Receptacle
Class 2 Output Power Pack Red Lighting
Neut. White
Load
24 VDC, 225 mA Switch
Black Red
Hot
Green
UL 2043 Plenum Rated
Ground
Control
Common Any 3-Wire
24VDC
+24VDC Sensor
www.legrand.us • 800.879.8585
Class 2 16094r1
wiring only
COM (Black)
Line (Black)
The configuration process establishes the appropriate parameters for the FSP-201B
operation. This is done through the FSIR-100 configuration tool. If no configuration
steps are taken, the sensor will use its default parameter values.
Neutral (White)
The FSIR-100 Wireless IR Configuration Tool is a handheld tool for changing defaults
and testing of WattStopper FSP-201B. It provides wireless access to the FSP-201B
sensors for parameter changes and testing.
The FSIR-100 display shows menus and prompts to lead you through each process. The
navigation pad provides a simple way to navigate through the customization fields.
Wiring with an
external DC
Within a certain mounting height of the sensor, the FSIR-100 allows modification of
power supply
the system without requiring ladders or tools; simply with a touch of a few buttons.
The FSIR-100 IR transceiver allows bi-directional communication between the
FSP-201B and the FSIR-100 configuration tool . Simple menu screens let you see
the current status of the sensor and make changes. It can change FSP-201B sensor
parameters such as high/low mode, sensitivity, time delay, cut off and more. With the
FSIR-100 you can also establish and store FSP-201B parameter profiles.
WIRING
Dimming
Ballast/Driver
Dim– (Gray)
Dim+ (Violet)
FSP-201B CONFIGURATION
USING THE FSIR-100 CONFIGURATION TOOL
BATTERIES
NAVIGATION
3
Ground Neutral
(Green) (White)
CTRL (Blue)
BZ-200 Power Pack
120 – 277 VAC (1 φ ), 50/60 Hz
20A Ballast/ELV/MLV/Tungsten/LED LISTED
16A E-Ballast/CFL
Appliance
Control
1HP @ 120/240VAC
88T9
20A 120VAC Plug Load – Receptacle
Class 2 Output Power Pack Red Lighting
Neut. White
Load
24 VDC, 225 mA Switch
Black Red
Hot
Green
UL 2043 Plenum Rated
Ground
Control
Common Any 3-Wire
24VDC
+24VDC Sensor
www.legrand.us • 800.879.8585
Class 2 16094r1
wiring only
COM (Black)
+VDC (Red)
Power
On/Off
FSP-2X1
HBP-111
Back
Left
Down
Line (Black)
IR tx/rx
BAT=
Home/Main
Menu
Up
Right/Next
Select