No: 27547 – 11/21 rev. 6
Catalog Number • Numéro de Catalogue • Número de Catálogo: FSP-212D
Country of Origin: Made in China • Pays d'origine: Fabriqué en Chine • País de origen: Hecho en China
DESCRIPTION AND OPERATION
The FSP-212D is a motion sensor that dims lighting from high to
low based on movement. This slim, low-profile sensor is designed
for installation inside the bottom of a light fixture with a 0-10V output
dimmable ballast or LED driver control.
The sensors use passive infrared (PIR) sensing technology that reacts to
changes in infrared energy (moving body heat) within the coverage area.
Once the sensor stops detecting movement and the time delay elapses
lights will go from high to low mode and eventually to an OFF position if
it is desired. Sensors must directly "see" motion of a person or moving
object to detect them, so careful consideration must be given to sensor
luminaire placement and lens selection. Avoid placing the sensor where
obstructions may block the sensor's line of sight.
The FSP-212D has a photocell to read the light level and can
continuously raise or lower the dimming level of the lighting loads, based
on the ambient light and the desired light level setting.
The FSP-212D operates at 120V/230V-240V Single Phase/277V.
It is designed to be installed in indoor and outdoor environments,
and provides easy to use selectable modes with several adjustable
parameters.
The FSP-212D offers four different control modes of operation, (plus
service and test modes) that can be selected using a rotary pot. Once
powered up, each mode has a factory default set of parameters.
Additionally, sensor adjustment is available for time delay and high/low
dim levels via rotary pots.
NOTE: The FSP-212D is not compatible with non-isolated LED drivers.
Several lenses are available for use with the FSP-212D. Lenses give coverage at mounting heights between 8' - 40' for applications
such as, offices, warehouses and outdoor use. Density and range of the coverage is determined by the type of lens and mounting
height. A lens with shroud option is also available. The shroud blocks light coming from the fixture, to prevent interference with the
photocell function of the sensor. Lens modules are IP66 rated when combined with an FSP-212D sensor mounted to an outdoor rated
fixture. See the FSP-Lx Coverage Guide for more information.
Wattstopper
Selectable Mode Continuous Dimming Line Voltage PIR Fixture Integrated Sensor
Détecteur pour intégration au luminaire à gradation continuelle er mode
sélectionable de tension de ligne
Sensor PIR de Voltaje de Línea con atenuación continua para luminarias y
Modo Seleccionable
Installation Instructions • Instructions d'Installation • Instrucciones de Instalación
Voltage .................................................. 120V/277V, 50/60Hz
Load Ratings
Class 1 Wiring ........................ 18AWG, Length 36" (91.44cm)
Operating Temperature ........... -40°F (-40°C) to 158°F (70°C)
Tightening Nut Torque .......................................... 25-30 in-lbs
Dimensions
Weight .............................................................5.29 oz (150 g)
Enclosure ...................................................IP66 (NEMA STD)
Coverage
* Not compatible with non-isolated LED drivers
Sensor Protection Cap
NOTE: Remove Cap before use
LENS OPTIONS
®
SPECIFICATIONS
................................. 230–240V, 50/60Hz, Single Phase
@ 230-240V .................. 0–300W Ballast or LED Driver*
@ 120V .......0–800W Tungsten, Ballasts or LED Driver*
@ 277V ....................... 0–1200W Ballast or LED Driver*
Motor @ 120V/277V............................................. 1/6 HP
Line Voltage ......................................Line, Neutral, Load
Low Voltage (Class 1) .........Dim + (purple), Dim – (pink)
Collar ....................................... 1.87" diameter (47.5mm)
Collar height ........................................... 0.64" (16.3mm)
Body .. 2.5"L x 1.5"W x .83"H (63.3mm x 38mm x 21.1mm)
FSP-L2 Lens @ 8' height ................... up to 44' diameter
FSP-L3 Lens @ 20' height ................. up to 40' diameter
FSP-L7 Lens @ 40' height ............... up to 100' diameter
Dimming/
Hold Off
Setpoint/
High Trim
10V
Adjust
Mode
Selection
PIR Sensor
Motion Indicator
Red LED
1V
Time
Delay
Light Sensor