LEGRAND Wattstopper FSP-301B Instructions D'installation

No: 25745 – 03/20 rev. 9
Catalog Numbers • Les Numéros de Catalogue • Números de Catálogo: FSP-301B, FSP-301B-S, FSP-301B-D
Country of Origin: Made in China • Pays d'origine: Fabriqué en Chine • País de origen: Hecho en China
Voltage ...............................................................12–32 VDC
Current Consumption ................................. 15 mA maximum
Wiring .......................................................................22 AWG
Operating Temperature ..........-40°F (-40°C) to 167°F (75°C)
Tightening Skirt/Nut Torque ................................ 25-30 in-lbs
Dimensions
Weight ............................................................... 2.8 oz (80 g)
Enclosure .................................................IP66 (NEMA STD)
Coverage
The FSP-301B is an IP66 rated motion sensor that dims lighting from high to
low based on movement.
Three configurations are available. The FSP-301B mounts inside the fixture
and the PIR lens connects to the FSP-301B through a 1.30" diameter hole
in the bottom of the fixture. The FSP-301B-S mounts to a fixture/enclosure
with a 1/2" knock out, via a nipple on the back. The FSP-301B-D has a drop
mount nipple, for mounting on to a pole, or to a fixture.
The sensor uses passive infrared (PIR) sensing technology that reacts to
changes in infrared energy (moving body heat) within the coverage area. Once
the sensor stops detecting movement and the time delay elapses, lights will go
from high to low mode and eventually to an OFF position if it is desired. Sensors
must directly "see" motion of a person or moving object to detect them, so careful
consideration must be given to sensor luminaire placement and lens selection.
Avoid placing the sensor where obstructions may block the sensor's line of sight.
The FSP-301B has a photocell that can read the light level and continuously
raise or lower the dimming level of the lighting loads, based on the ambient light and desired light level setting.
The FSP-301B operates at 12–32 VDC. It is designed to be installed in indoor and outdoor environments.
NOTE: When the FSP-301B is powered up the first time, it will use factory default parameters to operate. If adjustments are needed,
the Sensor Configuration mobile app must be used.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
All manuals and user guides at all-guides.com
Length .......... 36" (91.44cm), 30" (76.2cm) from nipple
Primary Voltage .................................. +VDC, Com, Ctrl
Control Output .................................. 100 mA maximum
Dimming Voltage .................Dim + (violet), Dim - (gray)
Collar ......................................1.30" diameter (33.0mm)
Collar height ..........................................0.64" (16.3mm)
Body .... 5.7"L x 2.3"W x 3.5"H (145mm x 60mm x 90mm)
FSP-L2 Lens @ 8' height ................. up to 44' diameter
FSP-L3 Lens @ 20' height ............... up to 40' diameter
FSP-L7 Lens @ 40' height ............. up to 100' diameter
DESCRIPTION AND OPERATION
Wattstopper
Low Voltage, Continuous Dimming, PIR Fixture Integrated Outdoor Sensor
In IP66 Enclosure with Bluetooth low energy technology
Basse Tension, Gradation Continue, Luminaire avec détecteur IRP
extérieur intégré dans un boitier IP66 avec Bluetooth basse consommation
Sensor PIR de bajo voltaje para luminarias de exterior, tipo IP66 con
función de Atenuación Continua y con Bluetooth de bajo consumo
Installation Instructions • Instructions d'Installation • Instrucciones de Instalación
SPECIFICATIONS
Adjustments and Features
High Mode .................................................0 V – 10 V
Low Mode ................................... 0 V – 9 V, Disabled
Time Delay .................... 30 seconds, 1 min – 30 min
Cut Off ............... Disable, 1 min – 59 min ,1 hr – 5 hr
Sensitivity ................ On-Fix, Off-Fix, Low, Med, High
Hold Off Setpoint ................ Auto, Disabled, 1–250 fc
Ramp Up ............................ Disabled, 1 sec – 60 sec
Fade Down ......................... Disabled, 1 sec – 60 sec
Photocell Setpoint for On/Off .......Disabled, 1–250 fc
Continuous Dimming ....................Disabled, 0–250 fc
Factory Defaults
High Mode .......................................................... 10 V
Low Mode ............................................................ 1 V
Time Delay ........................................................5 min
Cut Off ................................................................. 1 hr
Sensitivity .......................................................... High
Hold Off Setpoint .........................................Disabled
Ramp Up ......................................................Disabled
Fade Down ...................................................Disabled
Photocell Setpoint for On/Off .......................Disabled
Continuous Dimming ....................................Disabled
Sensor Protection Cap
NOTE: Remove Cap before use
®
Reset Button
PIR Sensor
Motion Indicator
Blue LED
Light
Sensor