Publicité
Les langues disponibles
Les langues disponibles
symbol
Mode
Rotary
hammering
hammering
only
Bit Adjustment
To Select an Operating Mode
•
Rotate the mode selector dial
to the symbol corresponding for the desired mode.
nOTE: The arrow on the mode selector dial
pointing at a mode symbol at all times. There are no
operable positions in between. It may be necessary to briefly
run the motor after having changed from 'hammering only'
to 'rotary' modes in order to align the gears or to postion the
chisel bit.
Indexing the Chisel Position (Fig. A)
The chisel can be indexed and locked into
24 different positions.
1. Rotate the mode selector dial
the
position.
2. Rotate the chisel in the desired position.
3. Set the mode selector dial
Only" position.
4. Twist the chisel until it locks in position.
Performing an Application (Fig. A, G)
WARNING: TO REDUCE THE RISK OF PERSONAL
INJURY, ALWAYS ensure workpiece is anchored or
clamped firmly. If drilling thin material, use a wood
"back‑up" block to prevent damage to the material.
WARNING: Always wait until the motor has come to
a complete standstill before changing the direction
of rotation.
1. Choose and install the appropriate chuck, adapter, and/
or bit onto to the tool. Refer to Bit and Bit Holder.
2. Using the mode selector dial
appropriate to desired application. Refer to
Operation Modes.
3. Adjust the side handle
4. Place the bit/chisel on the desired location.
5. Depress the trigger switch
the trigger switch, the faster the tool will operate. For
maximum tool life, use variable speed only for starting
holes or fasteners.
6. To stop the hammer, release the switch.
Recommendations for Tool Operation
•
Large (5/16" to 1/2" [7.9 mm to 12.7 mm]) holes in steel
can be made easier if a pilot hole (5/32" to 3/16" [4 mm
to 4.8 mm]) is drilled first.
•
When drilling, always apply pressure in a straight line
with the bit, but do not push hard enough to stall the
Application
Drilling into concrete
and masonry
Chipping
Chisel bit position
adjustment
4
so that the arrow points
4
must be
4
until it points towards
4
to the "Hammering
4
, select the mode
as necessary.
2
. The farther you depress
1
motor or deflect the bit. A smooth even flow of material
indicates the proper drilling rate.
•
If drilling thin material or material that is prone to
splinter, use a wood "back-up" block to prevent damage
to the work piece.
WARNING:
•
Do not use this tool to mix or pump easily
combustible or explosive fluids (benzine,
alcohol, etc.).
•
Do not mix or stir inflammable liquids
labelled accordingly.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service
center. If you need assistance in locating any accessory, please
contact D
WALT call 1-800-4-D
e
visit our website: www.dewalt.com.
Repairs
The charger and battery pack are not serviceable. There are
no serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should
be performed by a D
D
WALT authorized service center. Always use identical
e
replacement parts.
English
WALT recommended
e
WALT (1-800-433-9258) or
e
WALT factory service center or a
e
11
Publicité
