Publicité
Les langues disponibles
Les langues disponibles
EN
chemicals. To extend their life, whenever the spa shell is being
cleaned, the spa pillows should be removed and cleaned. Body
oils can be removed with a mild soap and water solution. ALWAYS
rinse off the spa pillows thoroughly to remove any soap residue.
If the spa is not going to be used for a long period of time(that is
during a vacation or if the spa is winterized), or when the spa water
is being super-chlorinated, the spa pillows should be removed
until the next use of the spa.
To remove and replace the spa pillows:
cushion with care.
CARE OF THE EXTERIOR
Your spa has a Pearlescent shell. Stains and dirt generally will
not adhere to your spa's surface. A soft rag should easily remove
most dirt. Stains and dirt generally will not adhere to your spa's
surface. Most household chemicals are harmful to your
spa's shell. Cleaning of the surface should only be done with
a non-abrasive, non-sudsing cleaner. Always thoroughly rinse
off any spa shell cleaning agent with fresh water. The use of a
spa polish is recommended after the spa shell has been dried,
to polish the surface.
SERVICE NOTES:
1. Iron and copper in the water can stain the spa shell if allowed to
go unchecked. Your dealer can recommend a stain and scale
inhibitor to use if your spa water has a high concentration of
dissolved minerals.
2. The use of alcohol or any household cleaners other than those
listed to clean the spa shell surface is NOT recommended.
DO NOT use any cleaning products containing abrasives or
of harsh chemicals is not covered under the warranty.
IMPORTANT: Some surface cleaners contain eye and skin
irritants. Keep all cleaners out of the reach of children and
use care when applying.
CARE OF THE SPA COVER
WARNING: The cover is a manual safety cover that meets
for spa safety covers when installed and used correctly
as of the date of manufacture. Non-secured or improperly
secured covers are a hazard. Open the cover to its fully open
position before use.
VINYL COVER
The vinyl spa cover is an attractive, durable foam insulation
product. Monthly cleaning and conditioning are recommended
to maintain its beauty.
To clean and condition the vinyl cover:
1. Remove the cover from the spa and gently lean it against a
wall or fence.
2. With a garden hose, spray the cover to loosen and rinse away
dirt or debris.
very mild soap solution (one teaspoon dishwashing liquid with
7.5 liters of water) or baking soda(sodium bicarbonate), scrub
the vinyl top in a circular motion. Do not let the vinyl dry with
water.
5. Rinse off the underside of the cover with water only (use no
soap), and wipe it clean with a dry rag.
SERVICE NOTE: To remove tree sap, use cigarette lighter
with a saddle soap solution immediately afterwards, then
wipe dry.
Important reminders:
DO remove snow buildup to avoid breakage of the foam core
from the additional weight of the snow.
DO lock cover lock straps to secure the cover when the spa is
not in use.
DO NOT
cover lock straps.
DO NOT walk, stand, or sit on the cover.
DO NOT place any metal or heat transferring object on the
cover or place any type of plastic tarp or drop cloth over the
cover as this may result in a melted foam core, which would
not be covered under the warranty.
DO NOT use any lifting mechanisms, chemicals or cleaners
except those recommended or its Authorized Sales and Service
Dealer.
SAND FILTER MAINTENANCE
perform the backwash operation on the basis of the instructions
provided by the pressure gauge on the selector valve. Therefore,
take note of the pressure indicated by the pressure gauge
during system start-up or at the end of a periodic backwash
(this value varies depending on the type of system and length
of the system piping, and it is normally less than 1 atm); when
this value increases by 0.2 atm max compared to the initial one,
To perform the backwash, stop all pumps,
position the selector valve to position (2) and then activate the
Also close the valve of the suction line from the compensation
from the spa.
After a few minutes, but, however, when the drain water is clean
"1", ball valves and switches in the normal working conditions).
of the sand mainly attributable to the high degree of water
hardness, but also to certain polluting substances that may
NOTE: as an indication, the sand may require replacing every
3-4 years, with use of the spa at "family" level and a degree of
water hardness of about 20°fr.
WINTERISING
In areas in which, during the winter, temperatures frequently
drop below 0°C and the spa is not used, we recommend
completely emptying the system (spa, compensation tank,
ATTENTION: As indicated, valves have been provided in
these areas to completely drain the piping that connects: spa,
compensation tank and spa-pack.
Instead, in areas where temperatures only occasionally drop
below 0°C, the spa can be kept running, as it is provided
with "anti-freeze" protection that ensures a minimum water
temperature (See "Temperature maintenance").
NOTE: DO NOT LEAVE WATER INSIDE THE SPA.
ATTENTION: When not in use, the Spa must be covered with
cold are not covered by warranty.
ALARM SIGNALS - SPA-PACK KEYBOARD
The presence of an alarm is signalled on the display, which shows
the code for the type of signal, and by the "set" key that lights up.
one with the lowest numerical code; pressing "set" interrupts the
signal and, if there is more than one alarm, displays the next one.
If the alarm condition persists, the respective code will continue
to be displayed.
38
Publicité
