Publicité
Les langues disponibles
Les langues disponibles
tank; however, it should only be used for short periods of time
6 - CLOSED: this position allows you to check for leaks in the
NOTE:
using the spa.
ATTENTION: Always handle the selector valve with the pump
stopped, so as to avoid dangerous overpressures.
SPA START-UP
ATTENTION: Preliminary checks and any system adjustments
CHECK:
the relative connections have been made (to the selector
valve and to the drainage well).
that installation is completed, that the pipes are bonded
with care and that the various sleeves and clamps ensure
perfect seal.
that the ball valves of the DRAIN pipes are CLOSED.
that the ball valves of the various spa connection piping of
the spa with the spa-pack and with the compensation tank
line, which must be properly calibrated for optimal system
operation; this adjustment is necessary whenever the system
NOTE:
Power the system using the main switches.
NOTE:
hose and with it any bacteria that may cause irritations.
Subsequently close the manual water loading since, when
the safety level switch located on the spa-pack is closed, the
automatic water loading into the compensation tank also starts,
through the solenoid valve.
NOTE: if the level indicator does not give its consent, the system
remains locked, including the loading solenoid valve.
Should the switch remain open due to an air bubble, the housing
When there is no water inside the compensation tank or it is below
the safety level, all spa functions controlled from the electric panel
are inhibited (except for water loading through solenoid valve).
This ensures the safety of the entire system (heating start, dry
pump start, etc.).
When the water level inside the compensation tank reaches the
maximum level switch, current to the loading solenoid valve of
the water mains is cut (because the operating level is reached).
NOTE:
level, taking water from the compensation tank. Should the water
level inside the compensation tank drop below the minimum level
switch, the latter will signal to top-up the water to the maximum
level, through the loading solenoid valve of the tank itself.
Check the spa functions.
Check for leaks from the hydraulic connections or other faults.
CHECK:
the water heating via the control panel; if the water
temperature is below that programmed, the heating system
activates automatically.
the whirlpool via the pneumatic buttons installed near the
spa; re-pressing the buttons stops the pumps (refer to the
relative chapter).
the functionality of the blower via the corresponding
pneumatic button.
button.
NOTE:
from the control panel on the electrical box.
ATTENTION: AFTER INSTALLING THE SPA, SUPER-
CHLORINATE TO DISINFECT THE TANK AND THE SYSTEM.
Do not use the Spa at the first start up, after super-
chlorination, given the high concentration of disinfectant
in the water during this phase.
and that
NOTE FOR SAFE OPERATION
otherwise you cannot correctly adjust the pH and disinfection
cannot be performed properly. The spa is ready for use only
after the water has been circulated and when the chlorine
level in the water is between 3 and 5 ppm.
SPA-PACK_KEYBOARD OPERATION
A control keyboard is installed on the "electrical box" of the Spa-
Pack through which it is possible to program the parameters of
the individual system functions.
1
DISPLAY: Indicator of temperature and session duration
1.
2.
ON/OFF key
3.
HEATER key
4.
5.
SET key (PARAMETERS/ALARM)
6.
TIMER key
7.
8.
CHROMOTHERAPY FLOODLIGHT key
Power the system.
All key LEDs and the display light up for a few moments and then
the display shows the current time (if previously set).
The keyboard is now in "COMMAND STAND-BY" ( mode with
the "ON/OFF" key off).
Pressing the "ON/OFF" key, it lights up and the system is
activated according to the previously set parameters (the water
temperature appears on the display).
The system is now in "SYSTEM ACTIVE" MODE.
When the "MANUAL" key is lit, it means that the control
keyboard is active, while if it is off, the pneumatic buttons
are active.
MANUAL" key pressed to activate the control
keyboard.
DATE AND TIME SETTING
With the keyboard in "COMMAND STAND-BY" mode, keep the
"TIMER" key pressed for a few seconds (the relative LED lights
29
EN
6
7
8
9
set
2
3
4
5
Publicité
