Publicité
Les langues disponibles
Les langues disponibles
scaling is caused by mineral content combined with high
pH. Additionally, scale forms more readily at higher water
temperatures.
Shock Treatment: Also known as "super-chlorination" when
chlorine is used. Shock treatment is a process of adding
remove chloramines and bromamines.
Total Alkalinity: The amount of bicarbonates, carbonates, and
hydroxides present in spa water. Proper total alkalinity is important
level. The desired range of TA in spa water is 125 to 150 ppm.
SPA WATER MAINTENANCE TROUBLESHOOTING GUIDE
CLOUDY WATER
:
-
Excessive oils / organic matter:
Improper sanitization:
Suspended particles / organic matter:
Overused or old water:
Ozone generator malfunctioning:
WATER ODOR
Excessive organics in water:
Improper sanitization:
-
Low pH:
-
CHLORINE ODOR
Chloramine level too high:
-
Low pH:
-
MUSTY ODOR
Bacteria or algae growth:
ORGANIC BUILDUP /SCUM RING AROUND SPA
Buildup of oils and dirt:
-
If severe, drain the spa, use a spa surfaceand tile cleaner to remove
ALGAE GROWTH
High pH:
- Shock spa with sanitizer and adjust pH
Low sanitizer level:
-
EYE IRRITATION
Low pH:
-
Low sanitizer level:
-
SKIN IRRITATION / RASH
:
-
Free chlorine level above 5 ppm:
-
STAINS
Total alkalinity and/or pH too low:
-
High iron or copper in source water:
-
SCALE
High calcium content in water – total alkalinity and pH too high:
-
ROUTINE AND SPECIAL MAINTENANCE
WARNING
- To ensure that the bath maintains its gloss throughout years,
do not use water over 60° C.
- Do not start the pump before the jets are completely covered
by water.
- Do not obstruct the jets when the pump is operating.
- Always stop the pump before emptying the bath.
AIR CONTROLS MAINTENANCE
sand or grit has become lodged inside the valve body. It is very
important that this debris is removed as soon as possible to avoid
damage to the valve. To accomplish this, follow this procedure:
1.Put the installation on/off switch to off.
2.Turn the air controls handle counter-clockwise as far as it will
go. Once the face stops rotating, use a little extra force to rotate
the face even more counter-clockwise past the locking position
until it stops. Pull face with the body away from the spa
3.Remove the valve body by pulling it upward.
4.Wipe the valve body and the interior walls of the valve clean.
5.Lubricate the o-rings with a waterproof lubricant available from
your dealer.
6.Reassemble the valve and turn power to the spa on.
JETS MAINTENANCE
If you notice that the jets spins slower than when the spa was
new, or the jets are sticking, the cause could be a build-up of
deposits inside the jets. To remove the deposits, use the following
instructions:
1. With the spa off, rotate the jet face counter-clockwise until it
stops.
2. Once the face stops rotating, use a little extra force to rotate the
face even more counter-clockwise past the locking position until
it stops. Pull face with the body away from the spa.
rotating eye, it should spin very freely. If it does not, place the
bearing end in a cup of vinegar (the vinegar will soften any
water and repeat the spin test.
NOTE: If it still doesn't spin freely than a second night of
to purchase a new bearing from your dealer.
rotate face body in either direction until you feel the body align
rotate the face clockwise using a little extra force to overcome
the locking position. If the face does not rotate, remove and
rotate face body 180°and repeat this step. Turn the pump on,
the jet should spin freely.
CARE OF THE SPA PILLOWS
The spa pillows will provide years of comfort if treated with care.
They have been positioned above the water level to minimize
the bleaching effects of chlorinated water and other s pa water
37
EN
Publicité
