Symbol Index; General Safety Precautions/Fcc & Ic Regulations; Warnings And Cautions - Warn Zeon Platinum Guide D'utilisation

Symbol Index for Advanced Wireless Remote Control
SYMBOL EXPLANATION
Auxiliary (Aux)
1
Auxiliary 1 (Aux 1)
2
Auxiliary 2 (Aux 2)
Brightness
Clutch Disengaged
Clutch Engaged
Clutch Disengagement
Function Error
Dual Auxiliary (Dual Aux)
Home
Unlinked from High Beam
Linked to High Beam
WARN INDUSTRIES

SYMBOL INDEX

SYMBOL EXPLANATION
Pairing
Power
Thermal Protection
Advanced Wireless
Remote Control Battery
Charge
Settings
Vehicle Battery Charge
Winching
Winch Motor Temperature
Winching In
Winching out
Wireless Signal Strength
3
GENERAL SAFETY PRECAUTIONS

Warnings and Cautions

As you read these instructions, you will see WARNINGS,
CAUTIONS, NOTICES and NOTES. Each message has a specifi c
purpose. WARNINGS are safety messages that indicate a potentially
hazardous situation, which, if not avoided could result in serious
injury or death. CAUTIONS are safety messages that indicate a
potentially hazardous situation which, if not avoided, could result
in minor or moderate injury. A CAUTION may also be used to alert
against unsafe practice. CAUTIONS and WARNINGS identify the
hazard, indicate how to avoid the hazard, and advise of the probable
consequence of not avoiding the hazard. NOTICES are messages to
avoid property damage. NOTES are additional information to help
you complete a procedure. PLEASE WORK SAFELY!
FCC Regulation
This device complies with Part 15 of the FCC Rule. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diff erent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
§ 15.21 Information to user.
The users manual or instruction manual for an intentional or
unintentional radiator shall caution the user that changes or
modifi cations not expressly approved by the party responsible
for compliance could void the user' s authority to operate the
equipment. In cases where the manual is provided only in a form
other than paper, such as on a computer disk or over the Internet, the
information required by this section may be included in the manual in
that alternative form, provided the user can reasonably be expected
to have the capability to access information in that form.
92821A3 92821A3
Industry Canada
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation
of the device.
Under Industry Canada regulations, this radio transmitter may only
operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.)
is not more than that necessary for successful communication.
This radio transmitter (identify the device by certifi cation number, or
model number if Category II) has been approved by Industry Canada
to operate with the antenna types listed below with the maximum
permissible gain and required antenna impedance for each antenna
type indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly
prohibited for use with this device.
WARN INDUSTRIES
4