Nice MhouseKit GD0N Instructions Et Avertissements Pour L'installation Et L'utilisation page 4

STEP 1
Important installer and user safety instructions.
• If this is the first time that you install a GD0N sectional or overhead door
automation system we recommend that you dedicate some of your time
to reading this manual. You should read it before you start installing the
system, so you do not have to rush to finish the work.
Keep all the components of the GD0N system handy so that you can
read, check and verify all the information contained in this manual. How-
ever, do not carry out the adjustment and memorisation stages otherwise,
during the actual installation of the products, you will have to deal with
settings that differ from the original factory ones.
• When reading this manual, pay special attention to the sections marked
by the following symbol:
these sections are particularly important for safety.
• Store this manual for future use.
• This manual, as well as the design and manufacture of the devices that
make up GD0N, comply fully with the standards and regulations in force.
• Considering the hazards that may exist during the installation and oper-
ation of GD0N, it is necessary that also the installation be carried out
in strict compliance with current legislation, standards and regulations,
particularly:
• This manual contains important information regarding personal
safety; before you start installing the components, it is important
that you read and understand all the information contained herein.
Do not proceed with the installation if you have doubts of any sort;
if necessary, refer to the Nice customer service department for
clarifications.
• Follow all the installation instructions.
• Before you start with the installation, make sure that each single
GD0N device is suitable for the intended automation purposes;
pay special attention to the data provided in chapter 6 "Techni-
cal characteristics". If even a single device is not suitable for the
intended application, do not proceed with the installation.
• Before you start with the installation, check whether additional
devices or materials are needed to complete the automation with
GD0N based on the specific application requirements.
• The GD0N automation system must not be installed outdoors.
• The GD0N automation system must not be used until the auto-
mation has been commissioned as described in paragraph 3.7.2
"Commissioning".
• The GD0N automation system cannot be considered as a suit-
able intrusion protection system. If you require efficient protection
you need to integrate GD0N with other devices.
• The packaging materials for GD0N must be disposed of in com-
pliance with local regulations.
• Do not make modifications to any components unless provided
for in this manual. This type of operations will only cause malfunc-
tions. Nice disclaims any liability for damage resulting from modi-
fied products.
• Components must never be immersed in water or other liquids.
Also during installation, do not allow liquids to enter the gearmo-
tor or other open devices.
4 – English
WARNINGS
• In the event that liquid substances have penetrated inside the
automation devices, immediately disconnect the power supply
and contact the Nice customer service department. The use of
GD0N in these conditions can be dangerous.
• Keep all components of GD0N away from heat sources and open
flames; these could damage the components and cause malfunc-
tions, fire or dangerous situations.
• Connect the gearmotor only to a power supply line equipped
with safety grounding system.
• All operations requiring the opening of the protection shell of the
GD0N must be performed with the gearmotor disconnected from
the power supply; if the disconnection device is not identifiable,
post the following sign on it: "WARNING: MAINTENANCE WORK
IN PROGRESS".
• In the event that any automatic switches or fuses are tripped,
you must identify the failure and eliminate it before you reset them.
• If a failure occurs that cannot be solved using the information
provided in this manual, refer to the Nice customer service depart-
ment.
Particular warnings concerning the suitable use of this product in relation
to the "Machinery" Directive 2006/42/EC:
• This product comes onto the market as a "machine component" and
is therefore manufactured to be integrated with a machine or assembled
with other machines in order to create "a machine", under the direc-
tive 2006/42/EC, only in combination with other components and in the
manner described in this instruction manual. As specified in the directive
2006/42/EC the use of this product is not admitted until the manufac-
turer of the machine on which this product is mounted has identified and
declared it as conforming to the directive 2006/42/EC.
Particular warnings concerning the suitable use of this product in relation
to the "Low Voltage" Directive 2006/95/EC:
• This product responds to the provisions foreseen by the "Low Voltage"
Directive if used in the configurations foreseen in this instruction manual
and in combination with the articles present in the Mhouse product cata-
logue.
These requirements may not be guaranteed if the product is used in con-
figurations or with other products that have not been foreseen; the use
of the product is prohibited in these situations until the correspondence
to the requirements foreseen by the directive has been verified by those
performing the installation.
Particular warnings concerning the suitable use of this product in relation
to the "Electromagnetic Compatibility" Directive 2004/108/EC:
• This product has been subject to tests regarding the electromagnetic
compatibility in the most critical of use conditions, in the configurations
foreseen in this instruction manual and in combination with articles pres-
ent in the Mhouse product catalogue.
The electromagnetic compatibility may not be guaranteed if the product is
used in configurations or with other products that have not been foreseen;
the use of the product is prohibited in these situations until the correspon-
dence to the requirements foreseen by the directive has been verified by
those performing the installation.