Accessory Functions - Elettro CF PRO MIG 565 TWO-PULSED Manuel D'instructions

3.2.2.1.4 Button L1 - Choice of filler material
With each press, the LED corresponding to the choice
will light.
LED M1 for iron,
LED N1 for aluminium,
LED O1 for stainless steel.
The LED P1 displays the choice of other special
types of wires. As a result of the choices made using the above
button L1:
The display S2
displays the welding programs that exist for the
various ypes of material, specifically:
if selected FE
if selected AL
if selected SS
if selected SP
The materials may be chosen using the button R2.
NOTE: This selection is active only with MIG processes.
The display U2
displays the welding programs that exist for the gas
types associated with the types of material, specifically:
if FE is selected
if Al is selected
if SS is selected
if SP is selected
The gas may be chosen using the torch trigger T2.
NOTE: This selection is active only with MIG processes.
NOTE: If, after setting your choices, there is no program to weld
the wire diameter selected, the displays S1 and C2 will display
the message NO-PRG.

3.2.2.2 ACCESSORY FUNCTIONS

3.2.2.2.1 H2 Button
When this button is pressed the display U2 shuts off and
the display S2 numerically displays the value of the size
selected. This is signaled by the corresponding LED, which
lights, and is adjustable via the buttons R2 and T2. If the
numerical value is not changed within 5 seconds, the displays
U2 and S2 return to the previous configuration.
NOTE: the last values shown on the display S2 are saved.
LED L2 Pre-gas
Adjustment Auto - 10 sec.
Active in all MIG processes and in TIG mode.
LED M2 Post-gas
Adjustment 0 - 30 sec.
Active in all MIG processes and in TIG mode.
SG2 etc.
AlSi 5, AlMg 5, Al 99,5 etc.
308L, 316L etc.
Al Bz8, CuSi 3, Rutile, Basic,
Metal, CrNi etc.
CO2, Ar 18CO2 etc.
Ar
Ar 2CO2, Ar 2O2 etc.
Ar, Ar 30He, Ar 18CO2 etc.
LED N2 Soft Start
Adjustment 1 - 100%
Active in all MIG processes.
It is the wire speed, expressed as a percentage of the speed set
for the welding, before the wire touches the workpiece.
NOTE: This adjustment it is important in order to always achieve
good starts.
Manufacturer setting "auto" automatic.
LED I2 "Hot start" current
Adjustment 1 - 200% of the welding current (adjusted with the
knob X).
Active in synergic MIG programs and in TIG mode when the
three-level welding mode has been selected (LED J1).
Active with "AHS-ON" see 3.2.2.5.2.
LED J2 Slope
adjustment 1 - 10 sec.
Defines the time for switching between the first "Hot start"
current and the second "welding" current, and from the second
to the third "crater filler" current.
Active in synergic MIG programs and in TIG mode. when the
three-level welding mode has been selected (LED J1).
Active with "AHS-ON" see 3.2.2.5.2.
LED K2 "Crater filler" current
Adjustment 1 - 200% of the welding current (adjusted with the
knob X). Active in synergic MIG programs and in TIG mode only
when three-level welding mode has been selected (LED J1).
Active with "AHS-ON" see 3.2.2.5.2.
LED O2 Burn - back
Adjustment 4 - 500 ms.
Serves to adjust the length of the wire leaving the contact tip
after welding. Active in all MIG processes. The higher the
number, the more the wire burns.
Manufacturer setting "auto" automatic.
LED P2 Hot - start for MMA
Adjustment 0 - 100%
Overcurrent output when the arc is first struck. Active in MMA.
LED Q2 Arc - force
Adjustment 0 - 100%
This is the adjustment of the dynamic characteristic of the pilot
arc. Active in MMA.
3.2.2.3 Displaying and adjusting the welding parameters.
Knob X
In relation to the type of process selected, this knob is used to
adjust the following values:
- synergic pulsed MIG and synergic MIG:
thickness (LED V1),
13