Settings; Commissioning - Scheppach DP16SL Traduction Du Manuel D'origine

8.6 Installing the sprocket chuck (23) (Fig. 8)
1. Clean the conical hole in the sprocket chuck
(23) and the spindle cone with a clean piece of
fabric. Ensure that no particles of dirt remain on
the surface. The smallest amount of contamina-
tion on one of the surfaces prevents the sprock-
et chuck (23) holding properly. This can cause
the drill bit to wobble. If the conical hole in the
sprocket chuck (23) is extremely contaminated,
use a cleaning agent on a clean piece of fabric.
2. Push the sprocket chuck (23) onto the spindle
nose as far as possible.
3. Turn the outer ring on the sprocket chuck (23)
counterclockwise (when viewed from above)
and open the jaws on the sprocket chuck (23).
4. Place a piece of wood on the machine table and
lower the spindle (33) until it touches the piece
of wood. Press tight so that the chuck is secure.
8.7 Install the box column drill on the work-
bench.
Screw the drill tight to a workbench using the holes on
the base plate (1) in order to prevent the machine tilting
However, for your own safety, a screw connection on
a workbench or similar is strongly recommended

9. Settings

Warning:
All required pre-settings for working properly with
your drill have already been made in the factory.
Please do not modify anything.
Normal wear and use of the tool can make subse-
quent adjustment necessary.
Warning:
Always pull the plug out of the socket prior to per-
forming setting work.
9.1 Setting the spindle return spring (Fig. 9 and
9.1)
The spindle return spring may have to be set, as it's
tension has changed and therefore, the spindle (33)
moves back too quickly or too slowly.
1. Lower the drilling table (18) for more space to
work.
2. Work on the left of the drill.
3. Insert a screwdriver into the front groove (28)
and keep this in position.
4. Use an open-ended spanner (size 14) to remove
the outer nut (29)
5. With the screwdriver still in the groove (28), loos-
en the inner nut (30) until the notch (31) releas-
es from the hub (32). ATTENTION, springs are
tensioned!
6. Turn the spring cap (27) carefully in an counter-
clockwise direction using the screwdriver until
you can press the groove (28) into the hub (32).
28 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
7. Lower the spindle (33) into the lowest position
and keep the spring cap (27) in position. Once
the spindle (33) moves up and down as you re-
quire, re-tighten the inner nut (30).
8. If it is too loose, repeat steps 3-5. If it is too tight,
repeat step 6 in reverse order.
9. Use an open-ended spanner to secure the outer
nut (29) against the inner nut (30).
10. NOTE: Do not over-turn and do not limit the
range of movement of the spindle (33)!
9.2 The axial play for the spindle (33) (Fig. 10)
When the spindle (33) is in the bottom position, turn it
manually. If you determine that the play is excessive,
proceed as follows:
1. Loosen the counternut (34).
2. Turn the screw (35) clockwise in order to com-
pensate for the play without impairing the up-
wards and downwards movement for the spindle
(33) (a small amount of play is normal).
3. Re-tighten the counternut (34).

10. Commissioning

Warning:
If you are not familiar with this type of machine, obtain
advice from a specialist. You must have read and un-
derstood the usage and safety information before you
work with this product.
10.1 ON/OFF switch (24)
• Switching on: Press the "I" button.
• Switching off: Press the "0" button.
10.2 Swivelling the table (Fig. 11+12)
Note:
The angle scale (19) is only intended as a rough
guideline for angle setting. Suitable protractors must
be used for precision work.
1. In order to move the drilling table (18) into the in-
clined position, use a size 19 open-ended span-
ner to undo the clamping screw (13) and remove
the screw (20) that is used for 90° fixing.
2. Use the angle scale (19) to set the required an-
gle.
3. Re-tighten the clamping screw (22).
10.3 Setting the table height (Fig. 11+12)
1. Loosen the clamping handle for height adjust-
ment (21).
2. Set the drilling table (18) to the required height
by cranking the adjustment handle for height ad-
justment (3).
3. Re-tighten the clamping handle for height ad-
justment (21).
Note:
We recommend setting the table height so that the tip
of the drill bit is just above the workpiece.