Program Mode; Basic Navigation - Hedson IRT 4-1 PCAUTO Mode D'emploi

7. Program mode - General rules for navigation in the software
– The display shows software defined options in the bottom corner fields.
To adjust the values use the arrow keys.
– To move to previous display without saving, press cancel
7.1

Basic navigation

There are twelve predefined programs and three empty ones. All 15 programs have editable positions, names and drying parameters. Scroll up or
down using the arrow keys, press select to run the program or view to edit.
1. Putty
2. Filler Bright
3. Filler Dark
4. Waterbase
5. Basecoat
6. Topcoat
7.2
7.2.1
The distance is indicated on the display as "too
close", "too far" or "correct". If measuring fails
"check distance manually" appears.
Use the buttons on the keyboard to alter between
one or two active cassettes and to turn on/off the
Stop or cancel
temp. control. See chapter 8.1.
returns to 7.1.
7.2.2
Press start to begin the drying sequence. The
remaining time of the "flash off" will start counting
down. When the count down is finished, the pro-
gram automatically changes to full bake mode.
7.2.3
This graph is available when the temperature con-
trol is active. The graph describes the target, actual
temperature, and remaining time. See chapter 8.1.
7.2.4
These are the same values as shown in program
graph (7.2.3), except for the remaining time, but
also the used power capacity of the machine and
the energy consumption of the current drying
process.
Note! An inactive temperature control does not
show temperature values.
7.2.5
Total energy consumption per drying process is
shown for the last 10 runs.
7.2.6
When flash off and full bake times have expired
the software returns to 7.1.
Note! To extend the lifetime of the lamps, the
ventilators will continue to run for cooling. After
three minutes they turn off automatically.
Note! When the drying program is completed the
temperature control will automatically reactivate.
713687 rev 9
7. Clearcoat
8. Plast Filler
9. Plast Topcoat
10. PlastiClearcoat
11. Final boost
12. Soft cure
Run
Distance check
Start drying
Program graph
Program values
Energy consumption
Drying complete
.
13. Free prog
14. Free prog
15. Free prog
7.3
7.3.1
The values of the chosen program will show on
the display. By pressing the "Temperature control"
button the software switches between the proper-
ties with and without the temperature control. A
Stop or cancel change in either property is independent of the
other one. See chapter 8.1 for more info.
returns to 7.1.
7.3.2
Use the arrow keys to set the correct digit. Press
enter to confirm and to edit the second, third and
fourth digit in the advanced PIN code.
Note! An entered PIN code is valid for all entries
until the main switch is turned off. See chapter 9.2
Use arrow keys
for "advanced PIN code".
to set numbers.
7.3.3
When marked, change the value of the parameters
with the arrow keys. Press enter to change the
next value and so on. Pressing enter for the last
value directs the user to editing of program posi-
tion and name.
Press cancel to exit to 7.3.1 without saving any
parameters.
The program returns
to 7.3.1.
7.3.4
When marked, change the program number with
the arrow keys. Press enter to confirm and to edit
the next symbol.
Note! Changing the number will also change the
program position in the program list.
7.3.5
The program returns
When the drying process requires more than the
to 7.3.1.
two standard steps, you can expand the number
of steps in the drying cycle by linking to the next
program.
Start from point 7.3.4 and press "Enter" repeat-
edly until the "Link to next program" appears on
the screen. Select with the arrow keys "Yes" or
"No", and then press "Save". The link to the next
The program returns program will remain until it is deactivated (No).
Use the program 13, 14 or 15 as these are free
to 7.3.1.
programs without any default.
Edit
Properties
PIN Code
Edit program parameters
Edit prog. position/name
Expansion of the program steps
5