Additional Safety Rules - Makita BO4900V Manuel D'instructions

ENGLISH
1 Clamp lever
2 Conventional type of abrasive
paper with pre-punched holes
3 Pad
4 Punch plate
5 Conventional type of abrasive
paper without pre-punched
holes
SPECIFICATIONS
Model
Pad size ......................................................... 115 mm x 229 mm
Abrasive paper size ....................................... 115 mm x 280 mm
–1
Orbits per minute (min
Sanding stroke rate (min
Overall length ................................................ 289 mm
Net weight ...................................................... 2.8kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for the sanding of large surface of
wood, plastics and metal materials as well as painted
surfaces.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Hold the tool firmly.
2. Do not leave the tool running. Operate the tool
only when hand-held.
3. This tool has not been waterproofed, so do not
use water on the workpiece surface.
4. Ventilate your work area adequately when you
perform sanding operations.
5. Some material contains chemicals which may be
toxic. Take caution to prevent working dust inha-
lation and skin contact. Follow material supplier
safety data.
6. Always use the correct dust mask/respirator for
the material and application you are working
with.
SAVE THESE INSTRUCTIONS.
Explanation of general view
6 Hook-and-loop type of
abrasive paper with
pre-punched holes
7 Pad for hook-and-loop type of
abrasive paper
8 Screws
9 Screwdriver
10 Groove
11 Front fixing cardboard
BO4900V
)................................ 4,000 – 10,000
–1
) ............................ 8,000 – 20,000
BO4900
115 mm x 229 mm
115 mm x 280 mm
10,000
20,000
289 mm
2.8kg
OPERATING INSTRUCTIONS
Installing or removing abrasive paper
CAUTION:
Always be sure that the tool is switched off and
unplugged before installing or removing the abrasive
paper.
For conventional type of abrasive paper with pre-
punched holes (standard equipment):
Turn the clamp lever counterclockwise. Insert the paper
end into the clamper, aligning the holes in the paper with
those in the pad. Then return the clamp lever to the origi-
nal position to secure the paper. Repeat the same pro-
cess for the other end of the tool, maintaining the proper
paper tension. (Fig. 1)
For conventional type of abrasive paper without pre-
punched holes (optional accessory):
Turn the clamp lever counterclockwise. Insert the paper
end into the clamper, aligning the paper edges even and
parallel with the sides of the base. Then return the clamp
lever to the original position to secure the paper. Repeat
ENB042-3
the same process for the other end of the tool, maintain-
ing the proper paper tension. Place the punch plate
(optional accessory) over the paper so that the guide of
the punch plate is flush with the sides of the pad. Then
press the punch plate to make holes in the paper.
(Fig. 2)
For hook-and-loop type of abrasive paper with pre-
punched holes (optional accessory):
Remove all dirt or foreign matter from the pad. Attach the
paper to the pad, aligning the holes in the paper with
those in the pad. (Fig. 3)
CAUTION:
Never use pressure-sensitive abrasive paper.
12 Paper dust bag
13 Claws
14 Upper part
15 Notch
16 Guide
17 Speed adjusting dial
18 Lock button
19 Switch trigger
BO4901
115 mm x 229 mm
115 mm x 280 mm
10,000
20,000
289 mm
2.8kg
5