Additional Safety Rules - Makita BO5010 Manuel D'instructions

ENGLISH
1 Abrasive disc
2 Skirt
3 Dust bag
4 Dust nozzle
SPECIFICATIONS
Model
Pad size .............................................................. 123 mm
-1
Orbits per minute (min
Dimensions (L x W x H) ...................150 x 123 x 145 mm
Net weight ............................................................. 1.2 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for the sanding of large surface of
wood, plastics and metal materials as well as painted
surfaces.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Hold the tool firmly.
2. Do not leave the tool running. Operate the tool
only when hand-held.
3. This tool has not been waterproofed, so do not
use water on the workpiece surface.
4. Ventilate your work area adequately when you
perform sanding operations.
5. Some material contains chemicals which may be
toxic. Take caution to prevent working dust inha-
lation and skin contact. Follow material supplier
safety data.
6. Always use the correct dust mask/respirator for
the material and application you are working
with.
SAVE THESE INSTRUCTIONS.
4
Explanation of general view
5 Groove
6 Front fixing cardboard
7 Front side of paper dust bag
8 Claws
) ...................................... 12,000
OPERATING INSTRUCTIONS
BO5010
Installing or removing abrasive disc (Fig. 1)
BO5011
CAUTION:
Always be sure that the tool is switched off and
unplugged before installing or removing the abrasive
disc.
For BO5010
To install the abrasive disc, first remove all dirt or foreign
matter from the pad. Then attach the abrasive disc to the
pad, using the hook-and-loop system of the abrasive disc
and the pad. Be careful to align the holes in the abrasive
disc with those in the pad.
To remove the disc from the pad, just pull up from its edge.
CAUTION:
Always use hook-and-loop system abrasive discs. Never
use pressure-sensitive abrasive discs.
For BO5011
To install the abrasive disc, first remove all dirt or foreign
matter from the pad. Then peel off the backing paper
from the abrasive disc and attach the abrasive disc to the
pad. Be careful to align the holes in the abrasive disc with
those in the pad.
CAUTION:
If you peel off the abrasive disc from the pad, its adhe-
sion will become poor. Never attempt to stick it onto the
pad for further use.
Installing dust bag (Fig. 2)
ENB042-3
Install the dust bag on the tool so that the Makita logo on
the dust bag will be upright (not upside down). The dust
bag can be swiveled 360°. Position the skirt so that the
dust bag will not interfere with your work.
Emptying dust bag
When the dust bag is about half full, switch off and
unplug the tool. Remove the dust bag from the tool. Then
remove the dust nozzle from the dust bag after unlocking
the dust nozzle by turning it slightly counterclockwise.
Empty the dust bag by tapping it lightly. (Fig. 3)
After emptying the dust bag, install the dust nozzle on the
dust bag. Turn the dust nozzle slightly clockwise to lock it
in place. Then install the dust bag on the tool as
described in ''Installing dust bag''. (Fig. 4)
Installing paper dust bag
To install the paper dust bag, place the paper dust bag on
the paper dust bag holder with its front side upward.
Insert the front fixing cardboard of the paper dust bag
into the groove of the paper dust bag holder. (Fig. 5)
Then press the upper part of the front fixing cardboard in
arrow direction to hook it onto the claws. (Fig. 6)
Insert the notch of the paper dust bag into the guide of
the paper dust bag holder. Then install the paper dust
bag holder set on the tool. (Fig. 7 & 8)
9 Upper part
10 Notch
11 Guide
12 Switch