Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
TIPS:
1) Mowing the lawn frequently and reducing the amount
of starting/stopping procedures will help conserve battery
runtime. It is recommended to always use the same two
batteries during operation with fully charged levels.
2) For the best cutting performance, it is recommended to only
mow up to 1/3 or less of the current grass height at a time. Mow
at a slower pace when cutting long/thick grass to allow the
mower to properly discharge the clippings.
MAINTENANCE
WARNING: Stop the mower and remove
batteriesbefore removing the grass collection
bag.
NOTE: To ensure long and reliable service, perform the
following maintenance procedures regularly. Check for obvious
defects such as a loose, dislodged or a damaged blade, loose
fittings, and worn or damaged components. Check that
the covers and guards are all undamaged and are correctly
attached to mower. Carry out any necessary maintenance or
repairs before operating mower. If the mower should happen
to fail despite regular maintenance, please call our customer
helpline for advice.
BLADE SHARPENING
KEEP BLADE SHARP FOR BEST MOWER PERFORMANCE. A
DULL BLADE DOES NOT CUT GRASS CLEANLY OR MULCH
PROPERLY.
WEAR PROPER EYE PROTECTION WHILE REMOVING,
SHARPENING, AND INSTALLING BLADE. ENSURE THE
BATTERIES ARE REMOVED.
Sharpening the blade twice during a mowing season is
usually sufficient under normal circumstances. Sand
causes the blade to dull quickly. If your lawn has sandy soil,
more frequent sharpening may be required.
REPLACE BENT OR DAMAGED BLADE IMMEDIATELY.
WHEN SHARPENING THE BLADE (See Fig. N)
1.
Make sure blade remains balanced.
2.
Sharpen blade at the original cutting angle.
3.
Sharpen cutting edges on both ends of blade to keep
it balanced, removing equal amounts of material from
both ends.
NOTE:
1.
Be sure the mower is turned off and remove batteries
2.
Place the mower in stand up storage mode.
BLADE BALANCING (See Fig. O)
Check balance of blade by placing center hole in blade
O-1 over a screwdriver shank O-2, clamped horizontally
in a vise O-3. If either end of the blade rotates downward,
file that end. Blade is properly balanced when neither end
drops.
BLADE MAINTENANCE (See Fig. P1, P2)
Replace your Mower Blade after 50 hours mowing or 2
years, which ever is the sooner-regardless of condition.
Follow these procedures to remove and replace the
Blade. You will need garden gloves (not provided) and a
spanner wrench (not provided) to remove the Blade. Make
sure batteries are not installed. Wedge a block of wood
between the blade and the mower deck to prevent the
blade from turningand unscrew the Blade Bolt counter-
clockwise using a spanner wrench, and then remove the
Blade.
Cordless Lawn Mower
To re-assemble, position the Blade with the cutting edges
towards the ground. Then securely tighten the Blade Bolt.
STORAGE (SEE FIG. M1, M2)
Stop the mower and remove batteries. Clean the exterior of
the machine thoroughly using a soft brush and cloth. Do not
use water, solvents or polishes. Remove all grass and debris,
especially from the ventilation slots.
Turn the machine on its side and clean the blade area. If grass
cuttings are compacted in the blade area, remove with a
wooden or plastic implement.
Store the machine in a dry place. Do not place other objects on
top of the machine.
To aid storage, release the Handle knobs, and rotate or fold the
Upper Handle.
FOR BATTERY TOOLS
The ambient temperature range for the use and storage of tool
and battery is 0
C-45
C (32
F-113
o
o
o
The recommended ambient temperature range for the
charging system during charging is 0
TROUBLE SHOOTING
Problem
1. Mower doesn't run
A. Release Operating Bail to turn
when Operating Bail
mower off. Remove batteries.
is activated.
Turn mower over and check that
blade is free to turn. If not free,
return to an authorized servicer.
Blade should turn freely.
B. Has battery been fully
charged? Plug in charger and
wait for green light to come on.
2. Motor stops while
A. Release Operating Bail to turn
mowing.
mower off. Remove batteries.
Turn mower over and check that
blade is free to turn. If not free,
return to an authorized servicer.
Blade should turn freely.
B. Raise cutting height of wheels
to highest position and start
mower.
C. Has battery been fully
charged? Plug in charger and
wait for green light to come on.
D. Avoid overloading the mower.
Slow down the cutting pace by
pushing mower slower or raise the
cut height. Or both.
F).
o
C-40
C (32
F-104
F).
o
o
o
o
Solution
EN
15
Publicité
Table des Matières
