Important - Worx NITRO Mode D'emploi

Power indicator light
See details in BATTERY STATUS part

IMPORTANT:

When only one light is illuminated,
your battery is overly discharged,
even though the machine may still
be capable to work. Continuing
to operate your machine with the
battery in this discharged condi-tion
may reduce the life and performance
of your battery.
When no light is illuminated, at least
one battery is not fully installed or
battery may be defective, please
double check the batteries are fully
seated into position.
Starting and Stopping
Operating the self-propel system.
Adjusting the cutting height
WARNING! Stop, release Operating
Bail and wait until the motor stops
before adjusting height. The blades
continue to rotate after the machine is
switched off, a rotating blade can cause
injury. Do not touch rotating blades.
LED headlight
Storage
14
BATTERY STATUS (See Fig. H)
• Before starting or after use, press the button beside the
power indicator light on the machine to check the battery
capacity.
• During operation, the battery capacity will be indicated
automatically by the battery power indicator. The
indicator constantly senses and displays the battery
condition as follows.
• Charge the machine with 2 battery packs with different
AH, the power indicator light displays the battery
condition with the lower one of the two batteries.
Battery power
indicator status
Five green lights
( ) are
illuminated.
Two, three or four
green lights are
illuminated.
Only one green
light ( ) is
illuminated.
No light is
illuminated.
Cordless Lawn Mower
See Fig. H
See Fig.I1,I2
See Fig.J
See Fig.K
See Fig. L
See Fig. M1,M2
Battery condition
The two batteries are in a highly
charged condition.
The two batteries have a remain-
ing charge. The more lights are
illuminated, the more battery
capacity.
The battery level of at least one
battery pack is very low. Please
check and charge the battery
pack.
At least one battery is not fully
installed or battery may be defec-
tive.
At least one battery is over
Only one light is discharged (please refer to the
flashing twice per battery charge condition), please
cycle. recharge the two batteries at
once before use again or storage.
Only one light is At least one battery is hot, wait
flashing three times for them cool down before start
per cycle. again.
Only one light is
The machine is over load. Raise
flashing four times
the cutting height or push slowly.
per cycle.
MULCHING MOWING TIPS
When using the mulching plug, your new mower is designed to
cut the grass clippings into small pieces and distribute them
back into the lawn, using mulching fins located inside the mower
deck.
Under normal conditions, the mulched grass will biodegrade
quickly to provide nutrients to the lawn. Please review
the following recommendations for optimum mulching
performance,
1) Avoid mowing when the grass is wet from rain or dew.
Wet grass may form clumps which interfere with the
mulching action and reduce runtime. The best time
to mow grass is in the late afternoon when the grass
is dry and the newly cut area will not be exposed to
direct sunlight.
2) For best mulching performance, set the cutting
height to remove about one third of the grass blade
length, ideally no more than 1.5" at one time. If the
lawn is overgrown, it may be necessary to increase
the cut height to reduce the pushing effort and
prevent overloading the motor. For extremely heavy
mulching, it is advisable to first cut at a high cut
height setting, and then re-cut to the final cut height.
Otherwise, make narrower cuts and mow slowly.
3) For best performance, keep the mower housing free
of built-up grass. From time to time turn mower off,
remove batteries and wait for the blade to come to
a complete stop. Turn mower on its side. Using an
object such as a stick, wipe out any accumulation
of grass in the blade area. Be careful of the sharp
edges of the blade. Clean often in wet, new grass, and
always after every use.
4) Certain types of grass or grass conditions may
require that an area be mulched a second time to fully
disperse the grass throughout the lawn. If cutting
a second time, it is advisable to cut perpendicular
(across) the first cut pattern. DO NOT CHANGE CUT
PATTERN IN ANY WAY THAT WOULD CAUSE MOWING
DOWN A HILL.
5) Change your cutting pattern from week to week. This
will help prevent matting and graining of the lawn.
CUTTING AREA
The cutting area can be affected by many factors including:
cutting height, operation practices (ex: starting/stopping),
lawn moisture levels, grass length and thickness.
It is ideal for mowing ¼ acre to /2 acre lot sizes.
1
EN