Symbols On The Tool - Metabo KFM 9-3 RF Mode D'emploi

substances: Ensure good ventilation of the
workplace and wear appropriate protective
equipment, such as respirators able to filter
microscopically small particles.
Observe the relevant guidelines for your material,
staff, application and place of application (e.g.
occupational health and safety regulations,
disposal).
Collect the generated particles at the source, avoid
deposits in the surrounding area.
Reduce dust exposure with the following measures:
- Do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits.
- Use an extraction unit and/or air purifiers
- Ensure good ventilation of the workplace and
keep clean using a vacuum cleaner Sweeping or
blowing stirs up dust
- Vacuum or wash the protective clothing Do not
blow, beat or brush
3.3 Special safety instructions for mains
powered machines:
Pull the plug out of the socket before making any
adjustments, changing tools, carrying out
maintenance or cleaning.
Use of a fixed extractor system is recommended.
Always install an RCD (GFCI) with a maximum trip
current of 30 mA upstream. When the machine is
shut down by the RCD (GFCI), it must be checked
and cleaned. See chapter 9. Cleaning.
3.4 Special safety instructions for cordless
machines:
Remove the battery pack from the machine before
making any adjustments, changing tools,
maintaining or cleaning.
Protect battery packs from water and
moisture!
Do not expose battery packs to fire!
Do not use faulty or deformed battery packs!
Do not open battery packs!
Do not touch contacts or short-circuit battery packs!
A slightly acidic, flammable fluid may leak
from defective Li-ion battery packs!
If battery fluid leaks out and comes into
contact with your skin, rinse immediately
with plenty of water. If battery fluid leaks out
and comes into contact with your eyes, wash them
with clean water and seek medical attention
immediately!
3.5

Symbols on the tool

........... Class II Construction
V............... volts
A .............. amperes
Hz ............ hertz
W ............. watts
~
.............. alternating current
........... direct current
rpm ......... revolutions per minute
.../min...... revolutions per minute
n ............. rated speed
4. Overview
See page 2.
1 Clamping screws
2 Spindle locking button
3 Additional handle
4 Slide switch
5 Handle
6 Speed adjustment wheel
7 Dust filter *
8 Electronic signal indicator *
9 Battery pack release button *
10 Capacity indicator button *
11 Capacity and signal indicator *
12 Battery pack *
13 Graduated collar
14 Adjusting ring
15 Scale
16 Knurled screw *
17 Ripping fence*
18 Support surface
19 Screw for fixing the ball bearing stationary seal
ring
20 Ball bearing stationary seal ring
21 Indexable insert
22 Fastening screw
23 Holder for indexable insert
*equipment-specific
5. Commissioning
5.1 For mains powered machines only
Before plugging in, check that the rated mains
voltage and mains frequency, as stated on the
type plate match your power supply.
Always install an RCD(GFCI) with a maximum
trip current of 30 mA upstream.
5.2 For cordless machines only
Dust filter
Always fit the dust filter (7) if the surroundings
are heavily polluted.
The machine heats up faster when the dust
filter (7) is fitted. It is protected by the
electronics system from overheating (see Section
10.).
To fit: See illustration A on page 2.
Fit the dust filter (7) as shown.
Removal: Holding the dust filter (7) at the edges,
raise it slightly and then pull it downwards and
remove.
Rotating battery pack
See illustration B on page 2.
The rear section of the machine can be rotated 270°
in 3 stages, thus allowing the machine's shape to be
ENGLISH en
7