Table Des Matières; Important Safety Information - Titan CAPSPRAY Maxum II 0277034 Notice D'utilisation

Important Safety Information

This symbol indicates a hazardous situation, which, if not
not avoided could result in death or serious injury.
To reduce the risks of fire or explosion, electrical shock
and the injury to persons, read and understand all
instructions included in this manual. Be familiar with the
controls and proper usage of the equipment.
HAZARD: EXPLOSION HAZARD DUE TO
INCOMPATIBLE MATERIALS
Will cause property damage or severe injury.
PREVENTION:
• Do not use materials containing bleach or chlorine.
• Do not use halogenated hydrocarbon solvents such as bleach,
mildewcide, methylene chloride and 1,1,1 - trichloroethane. They
are not compatible with aluminum.
• Contact your coating supplier about the compatibility of material
with aluminum.
HAZARD: GENERAL
Can cause severe injury or property damage.
PREVENTION:
• Read all instructions and safety precautions before operating any
equipment.
• Follow all appropriate local, state, and national codes governing
ventilation, fire prevention, and operation.
• The United States Government Safety Standards have been
adopted under the Occupational Safety and Health Act (OSHA).
These standards, particularly Part 1910 of the General Standards
and Part 1926 of the Construction Standard should be consulted.
• Use only manufacturer authorized parts. User assumes all risks
and liabilities when using parts that do not meet the minimum
specifications and safety devices of the manufacturer.
• Before each use, check all hoses for cuts, leaks, abrasion or
bulging of cover. Check for damage or movement of couplings.
Immediately replace the hose if any of these conditions exist.
Never repair a hose. Replace it with an identical replacement
hose.
• Do not spray outdoors on windy days.
• Wear clothing to keep paint off skin and hair.
• Never aim the spray gun at any part of the body.
HAZARD: HAZARDOUS VAPORS
Paints, solvents, insecticides, and other materials can be
harmful if inhaled or come in contact with the body. Vapors
can cause severe nausea, fainting, or poisoning.
PREVENTION:
• Use a respirator or mask if vapors can be inhaled.
Read all instructions supplied with the mask to be
sure it will provide the necessary protection.
• Wear protective eyewear.
• Wear protective clothing as required by coating
manufacturer.
HAZARD: SkIN BURN INjURy
Heated parts can cause severe skin burn injury.
PREVENTION:
• Quick disconnect fittings on the hose and spray gun become
hot during use. Avoid skin contact with quick disconnect fittings
when they are hot. Allow quick disconnect fittings to cool before
disconnecting the spray gun from the hose.
English
operating the equipment. Save theSe InStRuctIonS.
·
Read all safety information before
HAZARD: EXPLOSION OR FIRE
Solvent and paint fumes can explode or ignite. Property
damage and/or severe injury can occur.
PREVENTION:
• Provide extensive exhaust and fresh air introduction
to keep the air within the spray area free from
accumulation of flammable vapors.
• Avoid all ignition sources such as static electric
sparks, open flames, pilot lights, and hot objects.
Connecting or disconnecting power cords or
working light switches can make sparks.
• Do not smoke in spray area.
• Fire extinguisher must be present and in good working order.
• The power cord must be connected to a grounded circuit.
• Follow the material and solvent manufacturer's safety precautions
and warnings.
• Use extreme caution when using materials with a flashpoint
below 70° F (21° C). Flashpoint is the temperature that a fluid can
produce enough vapors to ignite.
• Plastic can cause static sparks. Never hang plastic to enclose
a spray area. Do not use plastic drop cloths when spraying
flammable materials.
Table of Contents
Safety ......................................................................................... 2
Service ....................................................................................... 3
Introduction ............................................................................... 3
Using an HVLP Spray Gun .................................................... 3-5
Preparing to Spray .............................................................. 3
Selecting a Spray Pattern.................................................... 3
Spray Pattern Size .............................................................. 4
Adjusting the Material and Air Flow ..................................... 4
Spraying .............................................................................. 4
Adjusting the Swivel Tube ................................................... 4
Cleaning your Spray Gun ........................................................ 5
Maintenance ........................................................................... 5-7
Adjusting the Packing Nut ................................................... 5
Replacing the Needle Packing and Air Valve Seals ............ 5
Replacing the Check Valve, Valve Seal, and Air Tubes...... 6
Replacing the Cup Gasket .................................................. 7
Converting to a Single Pin Trigger ......................................... 7
Using a Pressure Feed System ........................................... 7-8
Converting the Gun to Pressure Feed................................. 7
Connecting to a 2-Quart Remote Pressure Pot System...... 8
Converting the Gun to a Regulator Gun ................................. 8
Converting the Gun from Non-Bleeder to Bleeder ................ 8
Choosing a Projector Set ......................................................... 9
Changing a Projector Set .................................................... 9
Optional Accessories ............................................................... 9
Material reduction/projector set chart .................................. 10
Troubleshooting ..................................................................... 11
Turbine Cup Gun Parts List ............................................. 32-33
Turbine Pressure Feed Gun Parts List ........................... 34-35
Regulator Cup Gun Parts List ......................................... 36-37
Compressor Pressure Feed Gun Parts List ................... 38-39
Français ................................................................................... 12
Español.................................................................................... 22
Warranty .................................................................................. 42
2 © Titan Tool Inc. All rights reserved.