Bosch GCM 12 JL Professional Notice Originale page 30

OBJ_BUCH-1600-005.book Page 30 Friday, December 16, 2016 9:23 AM
30 | English
Technical Data
Mitre Saw
Article number
Rated power input
No-load speed
Reduced starting current
Laser type
Laser class
Divergence of laser line
Weight according to EPTA-Procedure 01:2014
Protection class
Permissible workpiece dimensions (maximum/minimum) see page 34.
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Mounting hole diameter
Noise/Vibration Information
Sound emission values determined according to
EN 61029-2-9.
Typically the A-weighted noise levels of the product are:
Sound pressure level 98 dB(A); Sound power level
111 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 61029-2-9: a
2
K=1.5 m/s .
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 61029 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for differ-
ent applications, with different accessories or poorly main-
tained, the vibration emission may differ. This may signifi-
cantly increase the exposure level over the total working
period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
1 609 92A 348 | (16.12.16)
3 601 M21 100
3 601 M21 130
3 601 M21 170 3 601 M21 160
W
-1
min
nm
mW
mrad (full angle)
kg
Assembly
mm 305
 Avoid unintentional starting of the machine. During
mm 1.7–2.6 assembly and for all work on the machine, the power
plug must not be connected to the mains supply.
mm 30
Delivery Scope
Carefully remove all parts included in the delivery from their
packaging.
Remove all packaging material from the machine and the
accessories provided.
Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
– Mitre saw with mounted saw blade
– Dust bag 1
2
<2.5 m/s , – Extraction adapter 2
h
– Material clamp 40
– Hex key 17
– Tilt-protector bar 44 with fastening set 47 (2 hex socket
screws, 2 washers)
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
All parts must be properly mounted and all conditions fulfilled
that ensure faultless operation.
Damaged protective devices and parts must be immediately
replaced by an authorised service centre.
Mounting the Tilt-Protector Bar (see figure A1)
Before using the power tool for the first time, the tilt-protec-
tor bar 44 must be mounted.
Use the "tilt-protector bar" fastening set 47 for mounting.
– Insert the tilt-protector bar 44 into the mounting holes pro-
vided in the base plate until the threaded holes of tilt-pro-
tector bar and base plate are flush.
GCM 12 JL
3 601 M21 190
3 601 M21 1P0
2000 1500
4300 4300
 
650 650
< 0.39 < 0.39
1M 1M
1.0 1.0
20.2 20.4
/II /II
Bosch Power Tools
1 800
4300

650
< 0.39
1M
1.0
20.2
/II