Maintenance, Cleaning, Repair; Ordering Replacement Parts - EINHELL BT-LC 700 D Mode D'emploi D'origine

Anleitung_BT_LC_700_D_SPK1:_
GB
Note: If the wood cannot be sawn completely in a
single cut, turn it over (reversing cut). To do this
return the feed carriage to its initial position, turn
the wood along the cut and saw through it again.
Important: If the saw blade (4) does not reach a
standstill after a maximum of 10 seconds, have
the switch checked by an authorized electrician
and replaced if necessary.
Pull the power plug immediately after finishing
work. Never leave the machine until you have
pulled the plug and secured the machine to
prevent its unauthorized use.
7.2. Changing the saw blade (Fig. 8-14)
Important: Pull the power plug!
Allow the saw blade to cool before you change it.
Do not use inflammable liquids to clean the saw
blade.
Always wear gloves when handling saw blades.
Risk of injury!
Remove the screw (20) from the cover plate (21)
and pull the cover plate downwards.
Remove the split pin (22) and washer (23) from
the rear end of the guide tube on the return spring
(10) and pull the entire feed carriage (6)
downwards and place it on the floor.
Place the locking bolt (24) in to the hole (34) away
from the flange (25) in the fixed saw blade cover
(2) and check that the saw blade (4) is locked.
The locking bolt (24) must pass right through the
fixed saw blade cover (2) and be visible on the
other side.
Undo the flange screw (26) by turning it counter-
clockwise.
Take the flange screw (26) and outer flange (25)
off the saw shaft (27).
The saw blade (4) can now be taken off the saw
shaft (27). Ensure that you do not lose the groove
spring (28) as you do this.
Carefully clean the saw blade (4), inner flange
(29), outer flange (25) and flange screw (26)
before re-assembly.
Fit the new saw blade following the above
instructions in reverse and tighten the flange
screw (26). Important: Do not tighten the flange
screws by tapping the tool (33) and do not use
any tool extensions. Ensure that the groove spring
(28) is fitted correctly and that the saw blade (4)
turns in the right direction.
Important: Remove the locking bolt (24) for the
changing the saw blade from the hole (34) in
the fixed saw blade cover (2) and insert the
bolt into the mounting (31) for it in the
machine frame (Fig. 14).
Pull the feed carriage (6) up again, thread the
return spring guide tube (10) back through the
18
15.04.2010 11:03 Uhr Seite 18
mounting (30). Then place the washer (23) back
on the guide tube and secure it with the split pin
(22).
Important: The tool (33) must be removed from
the flange screw. Keep the tool (33) for changing
the saw blade on the hook (32) provided for it on
the machine frame.
7.3. Transport (Fig. 2, 3, 15)
The chassis (9) means that the saw can be
transported by a single person.
Fit the transit lock (11) before transport.
To do this, remove the screw (14), move the
transport lock (11) towards the inside of the machine
and insert the screw (14) again. (Fig. 2)

8. Maintenance, cleaning, repair

Important! Pull out the power plug first.
Remove dirt regularly from the machine. Use a hand
brush or cloths for this purpose. Check the saw blade
for signs of wear at regular intervals. If it is not used
for a lengthy period, apply a thin coating of oil to the
saw blade and return spring (6) and the bearing (34)
for the feed carriage.
Blunt saw blades must be sharpened. Clean
resinified saw blades.
Check that all screw connections are secure at
regular intervals.
Keep the handles dry and free of resin, oil and
grease at all times. Never use caustic cleaning
products for cleaning purposes.
The saw must be covered with a tarpaulin if it is left
in unprotected areas or in outdoors. It is particularly
important to protect the motor and switch from water
contact.
Important: Repairs to electric tools may only be
carried out by a trained electrician.

9. Ordering replacement parts

Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info