Kärcher B 80 W Bp Mode D'emploi page 12

1 Spring element
2 Locking pin
3 Terminal strip cover
4 Lock of safety pin
5 Excenter lever
 Remove the terminal strip cover.
 Place the cleaning head halfway in front
of the appliance.
 Connect the mains supply cable of the
cleaning head to the appliance.
 Attach the terminal strip cover.
 Connect the hose couplers on the clean-
ing head to the hose on the appliance.
1 Push handle
2 Cleaning head
 Insert the push bow into the cleaning
head intake.
1 Safety splint
 Insert the safety splints into the holder
of the cleaning head from below.
1 Safety splint
2 Linchpin
 Insert the linchpin through the safety
splint and fold the safety rings forward.
12
1 Excenter lever
2 Locking pin
 Open the excenter lever of the slideable
intake on the lift arm.
 Press the cleaning head all the way
against the push handle.
Note: The less play the cleaning head
has after being installed, the less vibra-
tion will occur during cleaning.
 Move the intake and insert the safety
pin and lock it into place.
 Close the excenter lever.
 Swivel the water reservoir all the way
down, check the lock.
Dismantling the cleaning head
The removal will take place in the opposite
order of the installation.
CAUTION
When the cleaning head is removed, the
stability of the appliance can be compro-
mised; ensure a safe stance.
Possibly support the rear to prevent tipping.
Batteries
Please observe the following warning notes
when handling batteries:
Observe the directions on the bat-
tery, in the instructions for use and
in the vehicle operating instruc-
tions
Wear eye protection
Keep children away from acid and
batteries
Danger of explosion
Fire, sparks, naked flames and
smoking must be strictly avoided
Danger of chemical burns
First aid
Warning note
Disposal
Do not throw the battery into the
regular waste
10
-
US
Danger
Danger of explosion. Do not put tools or
other objects on the battery, i.e. on the ter-
minal poles and cell connectors.
Risk of injury. Ensure that wounds never
come into contact with lead. Always clean
your hands after having worked with batter-
ies.
Recommended batteries, B 80
Order No. Description
6.654-119.0 240 Ah - mainte-
1)
nance-free
6.654-124.0 180 Ah - mainte-
2)
nance-free
6.654-242.0 170 Ah - mainte-
3)
nance-free
6.654-086.0 180 Ah, - low mainte-
4)
nance
** Appliance requires 4 batteries
Complete set (24 V/240 Ah) incl. connect-
1)
ing cable, order no. 4.035-393.0
Complete set (24 V/180 Ah) incl. connect-
2)
ing cable, order no. 4.035-387.0
Complete set (24 V/170 Ah) incl. connect-
3)
ing cable, order no. 4.035-388.0
Complete set (24 V/180 Ah) incl. connect-
4)
ing cable, order no. 4.035-440.0
Insert batteries and connect
CAUTION
When the batteries are installed and re-
moved, the stability of the appliance can be
compromised; ensure a safe stance.
 Push the appliance forward about 2 m
so that the steering rollers point toward
the rear.
 Hold the wastewater reservoir by the
handle recess and swivel the reservoir
upwards toward the side.
 Insert all four batteries into the trough.
The 240 Ah batteries are seated flush in
the battery intake, no holding blocks are
required.
For the 170 Ah and 180 Ah batteries, 2
holding blocks must be installed in the
front and one in the right rear on the
floor. In addition to that, a foam strip is
inserted on the rear left.
Warning
Pay attention to correct poles.
1 Connecting cable of battery (-)
2 Connecting cable of battery (+)
3 short connecting cable
4 long connecting cable
 Connect the batteries as shown, use
the included connecting cables for this.
6 V**
6 V**
6 V**
6 V**