RIB K800 24V FCM FAST Mode D'emploi page 38

Masquer les pouces Voir aussi pour K800 24V FCM FAST:
Table des Matières

Publicité

G
B
EVENT
DIP 1 ON (hold-to-run mode)
Or failure of a safety device
DIP 2 ON (full stroke programming)
DIP 2 ON > DIP 1 ON (pedestrian stroke programming)
Programming sequence stopped due to intervention of a safety device
EVENT
No transmitter code entered
DIP 1 ON > DIP 2 ON - transmitter code programming for full opening
DIP 1 ON > DIP 3 ON - transmitter code programming for pedestrian
opening
DIP 1 ON > DIP 2 ON > DIP 3 ON - transmitter code programming for R-AUX
relay
Correct transmitter codes programming for full opening and R-AUX relay
Correct transmitter code programming for pedestrian opening
Remote control code not present in memory
Memory saturated by remote control codes (1000 codes saved)
Radio code deletion for full opening, pedestrian opening, R-AUX relay
EVENT
Stop button pressed
Photocell intervention
Edge intervention
Intervention of impact sensor
Failure of a safety device or safety device engaged for too long
Operation with emergency batteries (24 vdc)
Emergency batteries low signal
Operation with emergency batteries charged by solar panels
Alarm from edge
Impact sensor alarm
Failed photocells auto-test alarm
Encoder failure alarm
Functional block activated by smartphone
Achievement of set cycles
Energy saving activated by smartphone
TABLE SUMMARISING VISUAL AND SOUND ALARMS
SIGNALS DURING PROGRAMMING SEQUENCE
BUZZER STATUS
OFF
OFF
OFF
10 s tone with 2 s pause
BUZZER STATUS
OFF
OFF
OFF
OFF
1 Tone
1 Tone
OFF
OFF
2 Tones
WARNING SIGNALS DURING OPERATION
BUZZER STATUS
OFF
1 Tone
2 Tones
3 Tones
OFF
OFF
1 Tone every 5 s for 1 minute
(It is renewed by giving a command)
OFF
2 Tones every 5 s for 1 minute
(It is renewed by giving a command)
3 Tones every 5 s for 1 minute
(It is renewed by giving a command)
4 Tones every 5 s for 1 minute
(It is renewed by giving a command)
5 Tones every 5 s for 1 minute
(It is renewed by giving a command)
OFF
6 Tones every 5 s
(It is renewed by giving a command)
OFF
38
FLASHER STATUS
OFF
Flashes ON/OFF 250 ms
OFF
Flashes ON/OFF 500 ms
OFF
Flashes ON/OFF 500 ms
OFF
On steady
FLASHER STATUS
OFF
Flashes red/green
OFF
Flashes red for 10 s
OFF
Flashes green for 10 s
OFF
Flashes orange for 10 s
OFF
Turns green once
OFF
Turns red once
OFF
Red flash
OFF
Runs 6 green flashes
OFF
Runs 2 green flashes
FLASHER STATUS
LED STATUS AND SIGNAL OUTPUT
OFF
Led DL6 turns OFF
OFF
Led DL7-8 turns OFF
OFF
Led DL9-10 turns OFF
OFF
No led combined
OFF
Led DL1 flashes ON/OFF 250 ms
Flashes during
Signal output flashes ON/OFF twice for 250 ms
movement
followed by a pause of 2 s
Signal output flashes continuously ON/OFF for 500
OFF
ms
Signal output flashes ON/OFF 3 times for 250 ms
OFF
followed by a pause of 2 s
Flashes for 1 minute No led combined
Flashes for 1 minute No led combined
OFF
No led combined
OFF
Led DL14 OFF
OFF
Led DL12 is steady on green.
OFF
No leds matched
OFF
Blue led flashes once every 5 s
DL1 LED STATUS
DL10 LED STATUS

Publicité

Table des Matières
loading

Table des Matières