Maintenance And Service - Bosch GST Professional 65 Notice Originale

OBJ_BUCH-490-006.book Page 15 Wednesday, January 20, 2016 11:03 AM
Starting Operation
 Observe correct mains voltage! The voltage of the
power source must agree with the voltage specified on
the nameplate of the machine. Power tools marked
with 230 V can also be operated with 220 V.
Switching On and Off
To switch on the power tool, press the On/Off switch 2 and
keep it pressed.
To lock the pressed On/Off switch 2, push the lock-on button
1 toward the right or left.
To switch off the machine, release the On/Off switch 2. When
the On/Off switch 2 is locked, press it first and then release it.
To save energy, only switch the power tool on when using it.
Controlling/Presetting the Stroke Rate
(GST 65 E/GST 65 BE)
Increasing or reducing the pressure on the On/Off switch 2
enables stepless stroke-rate control of the switched-on ma-
chine.
Light pressure on the On/Off switch 2 results in a low stroke
rate. Increasing the pressure also increases the stroke rate.
When the On/Off switch 2 is locked, it is not possible to re-
duce the stroke rate.
With the thumbwheel for stroke rate preselection 3, the
stroke rate can be preset and changed during operation.
The required stroke rate is dependent on the material and the
working conditions and can be determined by a practical trial.
Reducing the stroke rate is recommended when the saw
blade engages in the material as well as when sawing plastic
and aluminium.
After longer periods of work at low stroke rate, the machine
can heat up considerably. Remove the saw blade from the ma-
chine and allow the machine to cool down by running it for ap-
prox. 3 minutes at maximum stroke rate.
Working Advice
 Before any work on the machine itself, pull the mains
plug.
 When working small or thin work pieces, always use a
sturdy support or a saw table (accessory).
Check wood, press boards, building materials, etc. for foreign
objects such as nails, screws or similar, and remove them, if
required.
Plunge Cutting (see figure E)
 The plunge cutting procedure is only suitable for treat-
ing soft materials such as wood, plaster board or simi-
lar! Do not work metal materials with the plunge cut-
ting procedure!
Use only short saw blades for plunge cutting. Plunge cutting is
possible only with the mitre angle set at 0°.
Place the machine with the front edge of the base plate 4 on
to the workpiece without the saw blade 6 touching the work-
piece and switch on. For machines with stroke rate control,
select the maximum stroke rate. Firmly hold the machine
against the workpiece and by tilting the machine, slowly
plunge the saw blade into the workpiece.
Bosch Power Tools
When the base plate 4 fully lays on the workpiece, continue
sawing along the desired cutting line.
Parallel Guide with Circle Cutter (Accessory)
For cuts using the parallel guide with circle cutter 18 (acces-
sory), the thickness of the material must not exceed a maxi-
mum of 30 mm.
Parallel Cuts (see figure F): Loosen the locking screw 17 and
slide the scale of the parallel guide through the lead 16 in the
base plate. Set the desired cutting width as the scale value
on the inside edge of the base plate. Tighten the locking
screw 17.
Circular Cuts (see figure G): Set the locking screw 17 to the
other side of the parallel guide. Slide the scale of the parallel
guide through the lead 16 in the base plate. Drill a hole in the
workpiece centred in the section to be sawn. Insert the
centring tip 19 through the inside opening of the parallel
guide and into the drilled hole. Set the radius as the scale
value on the inside edge of the base plate. Tighten the lock-
ing screw 17.
Coolant/Lubricant
When sawing metal, coolant/lubricant should be applied
alongside cutting line because of the material heating up.

Maintenance and Service

Maintenance and Cleaning
 Before any work on the machine itself, pull the mains
plug.
 For safe and proper working, always keep the machine
and ventilation slots clean.
Clean the saw blade holder regularly. For this, remove the saw
blade from the machine and lightly tap out the machine on a
level surface.
Heavy contamination of the machine can lead to malfunc-
tions. Therefore, do not saw materials that produce a lot of
dust from below or overhead.
 In extreme conditions, always use dust extraction as
far as possible. Blow out ventilation slots frequently
and install a portable residual current device (PRCD).
When working metals, conductive dust can settle in the in-
terior of the power tool. The total insulation of the power
tool can be impaired.
Lubricate the guide roller 5 occasionally with a drop of oil.
Check the guide roller 5 regularly. If worn, it must be replaced
through an authorised Bosch after-sales service agent.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
English | 15
1 609 92A 2BX | (20.1.16)