Operation; Setup; Filling The Battery (Pl6955 / Pl8955); Charge The Battery - Titan POWRLINER PL4955 0290052 Mode D'emploi

Operation

4. Operation
This equipment produces a fluid stream at extremely
high pressure. Read and understand the warnings
in the Safety Precautions section at the front of this
manual before operating this equipment.
4.1

Filling the Battery (PL6955 / PL8955)

Due to shipping regulations, the battery in your PowrLiner has been
shipped to you empty. Before using the PowrLiner, the battery
must be filled with electrolyte (acid) and then charged. Follow the
instructions below.
i
Battery electrolyte can be purchased at your local
hardware or auto parts retailer.
Battery electrolyte is very hazardous. Make sure
to follow all precautions and warnings on the
electrolyte container.
Electrolyte specifications
In cool or temperate climates, purchase electrolyte with a specific
gravity of 1.270 - 1.280.
In tropical climantes, purchase electrolyte with a specific gravity of
1.250 - 1.260.
Fill the battery
1. Remove the battery from the cart.
a. Remove the 12 gallon hopper from the cart.
b. Unscrew and remove the four (4) screws and washers that
secure the hopper plate to the cart. The top of the battery
should now be exposed.
2. Remove rubber sealing cap from the exhaust opening on the
side of the battery.
3. Replace the rubber sealing cap with the exhaust tube
provided (this can be found in the plastic bag containing the
instruction manual and other literature).
4. Remove the six (6) yellow filling caps on top of the battery.
5. Fill the battery with electrolyte in each of the filling ports (see
"Electrolyte specifications", above). Fill the battery to the
upper level as indicated on the battery case.
The electrolyte temperature must not be lower than
60º F (15º C) or higher than 86º F (30º C).
Attention
6. Allow the battery to stand for at least 30 minutes after filling.
7. After 30 minutes, check electrolyte level. If the level has fallen,
refill to the upper level prior to charging.
8. Replace the yellow filling caps.
9. Replace the hopper plate back onto the cart and secure using
the four (4) screws and washers.

Charge the battery

1. Place the battery on a charge for 3 to 5 hours at the
approximate current equivalent to 1/10th of its rated capacity.
a. If electrolyte level falls after charging, fill with distilled water to
upper level.
b. After water is added, continue charging for 1 to 2 hours in
order to mix the water with the electrolyte.
2. After charging, check the battery voltage three times at 30
minute intervals. Make sure the voltage is constant over the
three readings.
3. Replace the filler plugs (if needed) and wash off any
electrolyte spillage with clean water.
GB
4.2

Setup

1. Make sure the siphon hose (fig. 3, item 1) is connected to the
fluid section (2) and the bleed hose (3) is connected to the
bleed valve (4).
2. Install the gun support bar.
i
The spray gun, hose, and cables are mounted to the
gun support bar at the factory.
a. Loosen the tilt clamp knob (fig. 4, item 1) and lower the gun
support bar into position.
b. Loosen the support bar clamps (2) on each side of the cart.
c. Slide the gun support bar (3) through the cart.
d. Tighten the support bar clamps (2) to secure the gun support
bar in position.
i
The support bar height will need to be lower than
the cart frame to allow it to slide through the cart.
1
2
3
i
The gun support bar and the spray gun(s) can be
mounted on either side of the sprayer.
3. Position the first spray gun.
a. Disengage the trigger cable from the tensioning clamp.
8
4
3
2
1
PowrLiner