Maintenance And Re- Build Practices - Windsor Radius 28 Manuel D'utilisation

Maintain a safe distance from the edge of
ramps, platforms, and other similar working
surfaces.
When powered units are driven on and off
highway trucks or trailers, the brakes on the
highway trucks or trailers shall be applied
and wheel chocks or other positive me-
chanical means shall be used to prevent
unintentional movement of highway trucks
and trailers.
When powered units are driven on and off
semitrailers that are not coupled to a trac-
tor, supports may be needed to prevent up-
ending or corner dipping.
Report all accidents involving personnel,
building structures, and equipment to the
supervisor or as directed.
Do not add to, or modify the unit.
Do not block access to fire aisles, stairways
or fire equipment.
Traveling
Observe all traffic regulations including au-
thorized plant speed limits. Under normal
traffic conditions, keep to the right. Maintain
a safe distance, based on speed of travel,
from the unit ahead; keep the unit under
control all times.
Yield the right of way to pedestrians and
emergency vehicles such as ambulances
and fire trucks.
Do not pass another unit traveling in the
same direction at intersections, blind spots,
or at other dangerous locations.
Cross railroad tracks at an angle wherever
possible. Do not park closer than 6 ft (1800
mm) to the nearest rail of a railroad track.
Keep a clear view of the path of travel and
observe for other traffic, personnel, and
safe clearances.
Ascend or descend grades slowly, and with
caution. Avoid turning, if possible, and use
extreme caution on grades, ramps, or in-
clines; normally travel straight up and
down.
Under all travel conditions, operate the unit
at a speed that will permit it to be brought to
a stop in a safe manner.
Make starts, stops, turns, or direction rever-
sals in a smooth manner so as not shift load
and/or overturn the unit.
Do not indulge in stunt driving or horseplay.
Slow down for wet and slippery floors.
Before driving over a dockboard or bridge
plate, be sure that it is properly secured.
Drive carefully and slowly across the dock-
board or bridge plate, and never exceed its
rated capacity.
Do not drive units onto any elevator unless
specially authorized to do so. Do not ex-
ceed the capacity of the elevator. Approach
elevators slowly, and then enter squarely
after the elevator car is properly leveled.
Once on the elevator, neutralize the con-
trols, shut off power, and set brakes. It is
advisable that all other presonnel leave the
elevator before the unit is allowed to enter
or leave.
When negotiating turns, reduce speed to a
safe level consistent with the operating en-
vironment. Make the turns smoothly.
4 English
Motorized hand unit operation requires spe-
cial safety considerations as follows:
A never operate with greasy hands;
B foot protection is recommended;
C do not ride on the unit;
D keep feet clear of unit frame while oper-
ating.
E always keep hands and fingers inside
the protected area of the control handle;
F be cautious when traveling in reverse
due to steering characteristics;
G use caution when turning into an aisle;
H never travel at a speed greater than nor-
mal walking speed (approximately 3.5
mph [5.6 km/h]);
I always place both hands on the control
handle when operating;
J always operate with ohe hand on con-
trols.
Operator care of the unit
At the beginning of each shift and before
operating the unit, check its conditon, giving
special attention to the following:
A condition of tires
B if pneumatic tires, check inflation pres-
sures
C warning and safety devices
D lights
E battery
F controls
G chains and cables
H limit switches
I brakes
J steering mechanism
K additional items or special equipment as
specified by the user and/or manufac-
turer
If the unit is found to be in need of repair or
in any way unsafe, or contributes to an un-
safe condition, the matter shall be reported
immediately to the user's designated au-
thority, and the unit shall not be operated
until it has been restored to safe operating
condition.
If during operation the unit becomes unsafe
in any way, the matter shall be reported im-
mediately to the user's designated authori-
ty, and the unit shall not be operated until it
has been restored to safe operating condi-
tion.
Do not use open flames when checking
electrolyte level in storage batteries.
Do not make repairs or adjustments unless
specifically authorized to do so.
MAINTENANCE AND RE-
BUILD PRACTICES
Operation of the unit may be hazardous if
maintenance is neglected or repairs, re-
builds, or adjustments are not performed in
accordance with the manufacturer's design
criteria. Therefore, maintenance facilities
(on or off premises), trained personnel, and
detailed procedures shall be provided.
Parts manuals and maintenance manuals
may be obtained from the unit manufacturer.
In unusual cases not covered by the manu-
als referred above, consult the unit manu-
facturer.
Maintenance and inspection of the unit
shall be performed in conformance with the
following practices:
A a schedules planned maintenance, lu-
brication, and inspection system shall
be followed; consult the manufacturer's
recommendations;
B only tranined and authorized personnel
shall be permitted to maintain, repair, ad-
just, and inspect the unit, and in accor-
dance with manufacturer's specifications.
Before starting inspection and repair of the
unit:
A raise drive wheels free of floor or dis-
connect battery and use chocks or other
positive unit positioning devices;
B block chassis before working on them;
C disconnect battery before working on
the electrical system;
D the charger connector shall be plugged
only into the battery connector and nev-
er into the unit connector.
Operation of the unit to check performance
shall be conducted in an authorized area
where safe clearance exists.
A Before starting to operate the unit:
(1) be in operating position;
(2) apply break;
(3) place directional controls in neutral;
(4) turn switch to ON position;
(5) check function of steering, warning
devices, and breaks;
B Before leaving the unit:
(1) stop unit;
(2) place directional controls in neutral;
(3) apply the parking brake;
(4) stop the engine or turn off power;
(5) turn off the control circuit;
(6) if the unit must be left on an incline,
block the wheels.
Avoid fire hazards and have fire protection
equipment present in the work area. Do not
use any open flame to check the level or to
check for leakage of any fluid, especially
battery electrolyte. Do not use open pans of
fuel or flammable cleaning fluids for clean-
ing parts.
Properly ventilate work area, vent exhaust
fumes, and keep shop clean and dry.
Brakes, steering mechanisms, control
mechanisms, warning devices, articulating
axle stops, and frame members shall be
carefully and regularly inspected and main-
tanined in safe operating condition.