UFESA AP9000 Mode D'emploi page 16

The vacuum cleaner is equipped with
a power level memory function. When
you turn off the vacuum cleaner using
the ON/OFF button (8), the power level is going
to be stored in memory. After the vacuum
cleaner is turned on next time, it is going to start
working at the same power level it had been
working before it was turned off.
The vacuum cleaner is equipped with the
adjustment function for LED brightness
of the power level indicator (10) and the
clogged air inlet indicator (12) situated on the
control panel. To set demanded brightness of
LEDs you should simultaneously press the
power adjustment buttons + and – (9), and then
holding them down you should turn on the
vacuum cleaner by pressing the "ON/OFF"
button (8). The LED for power levels 1, 3, and 5
turn on, and the motor stays turned off. Next by
pressing the power adjustment buttons +/– (9)
you can respectively increase or decrease the
brightness of power level indicator (10), and the
clogged air inlet indicator (12). It is not possible
to change LED brightness for the pump
operation indicator (6). After setting a desired
LED brightness, it is necessary to turn off the
vacuum cleaner using the ON/OFF button (8).
In this way you leave the LED brightness
adjustment function mode, and the set LED
brightness level is stored.
The vacuum cleaner is equipped with
a power limiting function should the inlet
opening be clogged or the SAFBAG dust
bag full. It is manifested by a pulsing limitation
of the motor power and the lighting up of the
clogged air inlet indicator (12) while the vacuum
cleaner is operating at full power. In such a case
switch off the vacuum cleaner by pressing the
on/off button (8), unplug the appliance and
clear the tubes or replace the SAFBAG dust bag.
SAFBAG dust bag disassembly/assembly
● Remove the dry filtration module with the SAFBAG
(21) dust bag from the container.
1
Pull the SAFBAG dust bag interlock fastening and
pull the interlock aside.
2
Pull the fastening which attaches the SAFBAG dust
bag to the basket to release the dust bag plate.
3
Remove the dust bag.
4
Insert the SAFBAG dust bag so that the lower part
of the bag plate is in the slot of the housing. Press the
upper part of the bag plate to the fastening until you
hear a characteristic click and close the SAFBAG dust
bag interlock.
● Insert the dry filtration module with the SAFBAG (21)
dust bag to the container.
VACUUM CLEANING WITH THE USE OF
THE WATER FILTER MODULE
1
Press and hold the container lid opening button (2)
and lift the container lid.
2
Insert the partition to the grooves in the container
so that the shutters are directed downwards. Make sure
the partition is correctly mounted in the container i.e. the
partition fins should cover the protrusion in the container.
3
Fill the container with 1,3–1,5 liter of water. The water
level should be in the range marked on the wall of the
container.
Do not operate the appliance with an
empty container while vacuum cleaning
with the use of the water filter module.
4
Cover the container with the filter unit.
● Prepare the vacuum cleaner for operation according
B
to section
● The vacuum cleaner starts at the same power level
it had been working before it was turned off. Set the
desired power value by pressing the power adjustment
buttons +/- (9).
Do not operate the appliance for too
long without replacing the water in the
container.
WET VACUUMING AND WET CLEANING
Before using the wet cleaning function thoroughly
vacuum the surface to be cleaned.
Before operating the vacuum cleaner make sure the
container is empty and the water filter module and the
D
filters are clean.
1
Press and hold the container lid opening button (2)
and lift the container lid.
2
Remove the container together with the water filter
module (filter unit and partition) from the vacuum cleaner.
3
Remove the cleaning liquid container (23) by pulling
it by the handle and lifting it upwards.
.
E
F