Technical Data; Before Starting The Equipment - EINHELL GC-RT 1545 M Instructions D'origine

information on operating, maintenance and servi-
cing conditions.
For safety reasons, the machine may not be used
as a drive unit for other work tools or tool sets of
any kind.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

Voltage .....................................230-240V ~ 50Hz
Power input ............................................. 1500 W
Working width ............................................45 cm
Hoe diameter .............................................20 cm
Idle speed .............................................. 390 rpm
Number of blades .................................. 6 pieces
Danger!
Sound and vibration
L sound pressure level ..................... 80.4 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ..................... 91.57 dB(A)
WA
K uncertainty ........................................ 1.28 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
Anl_GC-RT_1545_SPK9.indb 17 Anl_GC-RT_1545_SPK9.indb 17
≤ 2.5 m/s
2
h
2
- 17 -
GB
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Assembly (Fig. 4-11)
•
Undo the split pin (Fig. 3/Item A) with washers
from both sides of the axle. Then push the
transport wheels onto the axle on both sides
as shown in Fig. 4 and secure with the split
pins and washers.
•
Press the wheel caps (Fig. 5/Item 11) onto
the transport wheels.
•
Push the cable strain-relief clip (Fig. 6a/Item
10.09.2020 13:55:03 10.09.2020 13:55:03