Technical Data - Scheppach HBS261 Traduction Des Instructions D'origine

• The machine is equipped with a safety switch to
prevent it being switched on again accidentally af-
ter a power failure.
• Before you use the machine for the first time,
check that the voltage marked on the rating plate
is the same as your mains voltage.
• If you use a cable reel, the complete cable has to
be pulled off the reel.
• Persons working on the machine should not be
distracted.
• Note the direction of rotation of the motor and
blade.
• Never dismantle the machines safety devices or
put them out of operation.
• Never cut workpieces which are too small to hold
securely in your hand.
• Never remove loose splinters, chips or jammed
pieces of wood when the saw blade is running.
• It is imperative to observe the accident prevention
regulations in force in your area as well as all other
generally recognized rules of safety.
• Note the information published by your profession-
al associations.
• Adjustable protective devices have to be adjusted
as close as possible to the workpiece.
• Important! Support long workpieces (e.g. with a
roller table) to prevent them sagging at the end
of a cut.
• Make sure the blade guard (3) is in its lower posi-
tion when the saw is being transported.
• Safety guards are not to be used to move or mis-
use the machine.
• Blades that are misshapen or damaged in any way
must not be used.
• If the table insert is worn, replace it.
• Never operate the machine if either the door pro-
tecting the blade or the detachable safety device
are open.
• Ensure that the choice of blade and the selected
speed are suitable for the material to be cut.
• Do not begin cleaning the blade until it has come
to a complete standstill.
• For straight cuts of small workpieces against the
longitudinal limit stop the push stick has to be
used.
• The bandsaw blade guard should be in its lowest
position close to the bench during transport.
• For miter cuts when the table is tilted, the paral-
lel stop must be positioned on the lower part of
the table.
• When cutting round timber, use a suitable holding
device to prevent the workpiece turning.
• Never use guards to lift or transport items.
• Ensure that the bandsaw blade guards are used
and correctly adjusted.
• Keep your hands a safety distance away from the
bandsaw blade. Use a push stick for narrow cuts.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• The push stick has to be stored on the intended de-
vice, so that it can be reached from normal working
position and is always ready to be used.
• In the normal operating position the operator is in
front of the machine.
• When sawing wood, connect the band saw to a
dust collection device.
• When cutting round or irregularly shaped wood,
use a suitable holding device that prevents the
workpiece from twisting.

6. Technical data

Electro motor
Power
Revolutions
Saw band length
Saw band width
Saw band width max.
Saw band speed I
Saw band speed II
Cutting height
Opening width
Table size
Slewing range of the table
size of workpiece max.
Weight
The work piece must have a minimum height of 3 mm
and a minimum width of 10 mm.
* Duty type S2 – Short-time duty.
Operation at constant load for 20 minutes or less, fol-
lowed by a time de-energized and at rest of sufficient
duration to re-establish machine temperatures within
2 K of the ambient temperature.
The total noise values determined in accordance
with EN 61029.
sound pressure level L
pA
uncertainty K
pA
sound power level L
WA
uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing.
Total vibration values (vector sum - three directions)
determined in accordance with EN 61029.
220 - 240 V ~, 50 Hz
550 W (S2 20 min)
1400 min
-1
1790 mm
6 mm
13 mm
660 m/min
960 m/min
0 - 120 mm
245 mm
300 x 300 mm
0° - 45°
580 x 400 x 120 mm
24 kg
77,4 dB(A)
3 dB
90,4 dB(A)
3 dB
GB | 29