Storage And Transport - EINHELL BG-BC 25 S Mode D'emploi

Anleitung_BG_BC_25_S_SPK7:_
GB
Important: Never clean the air filter with petrol or
inflammable solvents.
8.3 Maintenance of the spark plug
Spark plug sparking gap = 0.6mm. Tighten the spark
plug with a torque of 12 to 15 Nm. Check the spark
plug for dirt and grime after 10 hours of operation and
if necessary clean it with a copper wire brush.
Thereafter service the spark plug after every 50 hours
of operation.
1. Pull off the spark plug boot (Fig. 11a) by twisting.
2. Remove the spark plug (Fig. 11b) with the
supplied spark plug wrench.
3. Assemble in reverse order.
8.4 Grinding the safety hood blade
The safety hood blade can become blunt over time.
When you notice this, undo the two screws holding
the safety hood blade to the safety hood. Clamp the
blade in a vise. Sharpen the blade with a flat file and
make sure that the angle of the cutting edge is not
altered in the process. File in one direction only.
8.5 Carburetor settings
Important. Settings on the carburetor may only be
made by authorized customer service personnel.
The air filter cover must be removed before any work
on the carburetor, as shown in Figures 10a and 10b.
Setting the throttle cable
If the maximum speed of the equipment falls over
time and you have ruled our all the other causes listed
in section 11 Troubleshooting, it may be necessary to
adjust the throttle cable.
First of all check whether the carburetor opens fully
when the throttle handle is pressed fully. This is the
case if the carburetor slide (Fig. 13a/Item A) rests
against the stop (Fig. 13a/Item B) when the throttle is
fully open. Figure 13a shows the correct setting. If the
carburetor slide does not touch the stop, it must be
adjusted.
The following work is required to adjust the throttle
cable:
Undo the lock nut (Fig. 13b/Item C) a few turns.
Undo the adjusting screw (Fig. 13b/Item D) until
the carburetor slide rests against the stop when
the throttle is fully open, as shown in Figure 13a.
Retighten the lock nut.
Setting the idling speed
Important. Set the idling speed when the equipment
is warm.
If the engine stalls when the throttle is not pressed
and you have ruled out all the other causes listed in
section 11 Troubleshooting, the idling speed must be
adjusted. To do this turn the idling speed screw (Fig.
24
19.07.2010 8:35 Uhr Seite 24
13b/Item E) clockwise until the equipment runs
smoothly at idling speed. If the idling speed is so fast
that the cutting tool turns as well, it has to be reduced
by turning the idling speed screw for as long as is
required for the cutting tool to stop turning as well.
8.6 Environmental protection
Dispose of soiled maintenance material and
operating materials at the appropriate collection point.
Recycle packaging material, metal and plastics.
8.7 Ordering replacement parts
Please provide the following information on all orders
for spare parts:
Model/type of the equipment
Article number of the equipment
ID number of the equipment
Spare part number of the required spare part
For our latest prices and information please go to
www.isc-gmbh.info

9. Storage and transport

9.1 Storage
Important: Never put the equipment into storage for
longer than 30 days without carrying out the following
steps.
Storing the equipment
If you intend to store the equipment for longer than 30
days, the equipment must be prepared accordingly.
Otherwise the fuel still remaining in the carburetor will
evaporate and leave a rubbery sediment. This can
cause problems when starting up the equipment and
may require expensive repairs.
1. Slowly remove the fuel tank cap to release any
pressure that may have formed in the tank.
Carefully empty the tank.
2. Start the engine and let it run until the equipment
stops in order to remove any fuel from the
carburetor.
3. Leave the engine to cool (approx. 5 minutes).
4. Remove the spark plug (8.3).
5. Add one teaspoon of 2-stroke engine oil into the
combustion chamber. Slowly pull the starter cord
several times to apply a layer of oil to all internal
components. Fit the spark plug again.
Note: Store the equipment in a dry place and far
away from possible ignition sources such as an oven,
a gas-fired hot water boiler, a gas-fired dryer, etc.