Flow Volume Table; Maintenance And Cleaning Of Airless Hard-Metal Tips; Spray Gun Accessories - WAGNER EP 2800 Spacspray Mode D'emploi

Flow volume table

Tip
ø mm ø inch (")
0.18 0.007
0.23 0.009
0.28 0.011
0.33 0.013
0.38 0.015
0.46 0.018
0.53 0.021
0.66 0.026
0.79 0.031
0.91 0.036
1.10 0.043
1.30 0.052
*Flow volume refers to water.

Maintenance and cleaning of Airless hard-metal tips

Standard tips
If a different tip type has been fitted, then clean it according to manufacturer's instructions.
The tip has a bore processed with the greatest precision. Careful handling is necessary to achieve long durability.
Do not forget the fact that the hard-metal insert is brittle! Never throw the tip or handle with sharp metal objects.
The following points must be observed to keep the tip clean and ready for use:
1. Open the relief valve (valve position k).
2. Switch off unit.
3. Dismount the tip from the spray gun.
4. Place tip in an appropriate cleaning agent until all coating material residue is dissolved.
5. If there is pressure air, blow out tip.
6. Remove any residue by means of a sharp wooden rod (toothpick).
7. Check the tip with the help of a magnifying glass and, if necessary, repeat points 4 to 6.

Spray gun accessories

Flat jet adjusting tip
up to 250 bar (25 MPa)
Bore
Tip marking mm
15 0.13 - 0.46
20 0.18 - 0.48
28 0.28 - 0.66
41 0.43 - 0.88
49 0.53 - 1.37
Tip extension
with
slewable knee joint
(without tip)
Length 100 cm
Length 200 cm
Length 300 cm
Spray angle
10-20-50°
10-20-40-50-60°
10-20-40-50-60-80°
10-20-40-50-60-80°
10-20-40-50-60-80°
20-40-50-60-80°
20-40-50-60-80°
20-40-50-60-80°
40-50-60-80°
40-50-60-80°
50-60-80°
50°
Spray width at about 30 cm
removal of spray object
Pressure 100 bar (10 MPa)
5 - 35 cm
5 - 50 cm
8 - 55 cm
10 - 60 cm
10 - 40 cm
Order no. 0096 015
Order no. 0096 016
Order no. 0096 017
g
at 70 bars
0.16
0.23
0.30
0.45
0.61
0.95
1.25
1.90
2.84
3.79
5.69
7.60
Flat jet
Use adjusting tip
Order no.
Paints 0999 057
Paints, fillers 0999 053
Paints, dispersions 0999 054
Rust protection
paints - dispersions 0999 055
Large-area coats 0999 056
Tip extension
Length 15 cm
Length 30 cm
Length 45 cm
Length 60 cm
29
Flow volume in l/min*
at 100 bars
0.19
0.26
0.38
0.57
0.72
1.14
1.56
2.32
3.50
4.56
6.84
9.12
Contact protection
for the flat jet adjustment tip
Order no. 0097 294
Order no. 0999 320
Order no. 0999 321
Order no. 0999 322
Order no. 0999 323
at 150 bars
0.26
0.30
0.47
0.69
0.91
1.40
1.90
2.80
4.20
5.50
8.30
11.10