Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Report prepared for: Guillaume Thibodeau-Fortin (Stove Builder International Inc.) on 9/6/2018 2:01:07 PM
Test report 103536746MTL-002 (12 of 21)
TEST REPORT FOR STOVE BUILDER INTERNATIONAL INC.
Report No.: 103536746MTL-002
Date: 07/13/18
V
= Volume of gas sample as measured by dry gas meter, dcm (dcf).
m
V
= Volume of gas sampled corrected for the post test leak rate, dcm (dcf).
mc
V
= Volume of gas sample as measured by dry gas meter during each 10-min interval, i, of
mi
the test run, dcm.
V
= Volume of gas sample measured by the dry gas meter, corrected to standard
m(std)
conditions.
where:
K
= 0.3855 K/mm Hg for SI units and = 17.64 R/in. Hg for inch-pound units.
1
where:
V
= Vm– (Lp– La)u
mc
V
= Volume of room air sample as measured by dry gas meter, dcm (dcf), and
mr
V
= Volume of room air sample measured by the dry gas meter, corrected to standard
mr(std)
conditions.
Where:
K
= 0.3855 K/mm Hg for SI units and = 17.64 R/in. Hg for inch-pound units, and
1
V
= Average gas velocity in the dilution tunnel.
s
V
= Average gas velocity in dilution tunnel during each 10-min interval, i, of the test run.
si
V
= Average gas velocity at the center of the dilution tunnel calculated after the Pitot tube
scent
traverse.
V
= Average gas velocity calculated after the multipoint Pitot traverse.
strav
Y
= Dry gas meter calibration factor.
ΔH
= Average pressure at the outlet of the dry gas meter or the average differential
pressure across the orifice meter, if used, mm water (in. water).
ΔP
= Average velocity pressure in the dilution tunnel, mm water (in. water).
avg
ΔP
= Velocity pressure in the dilution tunnel as measured with the Pitot tube during each
i
10-min interval, i, of the test run.
where:
ΔP
= Velocity pressure in the dilution tunnel as measured with the Pitot tube at the
i(b)
beginning of each 10-min interval, i, of the test run, mm water (in. water), and
ΔP
= Velocity pressure in the dilution tunnel as measured with the Pitot tube at the end of
i(e)
each 10-min interval, i, of the test run, mm water (in. water).
θ
= Total sampling time, min.
10
= ten min, length of first sampling period.
13.6
= Specific gravity of mercury.
100
= Conversion to percent.
Version: 05/10/17
Stove Builder International Inc. | 44826 | Rev: Aug 31 2018 3:17PM | Uncontrolled Copy
V
= K
V
Y [(P
+ (ΔH/13.6))/T
m(std)
1
m
bar
V
= K
V
Y [(P
+ (ΔH/13.6))/T
m(std)
1
mc
bar
V
= K
V
Y [(P
+ (ΔH/13.6))/T
m(std)
1
mr
bar
V
= F
K
C
(√ΔP
)(√(T
/P
M
))
s
p
p
p
avg
s
s
s
V
= F
K
C
(√ΔP
)(√(T
/P
M
))
si
p
p
p
i
si
s
s
ΔP
= (ΔP
+ ΔP
)/2
i
i(b)
i(e)
]
m
]
m
]
m
Page 12 of 21
8431 Murphy Drive
Middleton, WI 53562
Telephone: 608-836-4400
Facsimile: 608-831-9279
www.intertek.com/building
GFT-OP-10c
Page 167 of 201
Publicité
Chapitres
Table des Matières
