Ego Power+ RTA2300 Traduction Des Instructions D'origine page 6

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 16
EN
Front-assist handle
Valuation of
vibration a
:
h
Rear handle
The declared vibration total value has been measured
in accordance with a standard test method and may be
used for comparing one tool with another;
The declared vibration total value may also be used in
a preliminary assessment of exposure.
NOTICE:
The vibration emission during actual use of the
power tool can differ from the declared value in which the
tool is used; In order to protect the operator, user should wear
gloves and ear protectors in the actual conditions of use.
PACKING LIST (FIG. A1)
DESCRIPTION
KNOW YOUR ROTOCUT ATTACHMENT (Fig. A1)
1. Sealing Screw
2. Gear Case
3. Blade
4. Sliding Cover Assembly
5. Guard Assembly
6. Shaft
7. End cup
8. Wrench
9. Allen Key
ASSEMBLY
WARNING:
If any parts are damaged or missing, do
not operate this product until the parts are replaced. Use of
this product with damaged or missing parts could result in
serious personal injury.
WARNING:
Do not attempt to modify this product
or create accessories not recommended for use with this
machine. Any such alteration or modification is misuse and
could result in a hazardous condition leading to possible
serious personal injury.
MOUNTING THE GUARD
WARNING: Always wear gloves when mounting
or replacing the guard. Take care of the blade on the
guard and protect your hand from cutting.
WARNING: Never operate the tool without the
guard firmly in place. The guard must always be on the
6
ROTOCUT ATTACHMENT—RTA2300
tool to protect the user! When the guard is fixed, never
3.3 m/s
2
attempt to remove or adjust the guard, if a replacement
K= 1.5 m/s
2
is needed, it should be performed by a qualified service
2.0 m/s
2
technician!
K= 1.5 m/s
2
Loosen and remove the two screws from the guard (Fig.
B), align the guard mounting holes with the assembly
holes and then lock the guard onto the shaft base with the
two screws, together with two spring washers (Fig. C).
WARNING:
Fig. B & C, any reverse fixing will cause great danger!
CONNECTING THE ROTOCUT ATTACHMENT TO THE
POWER HEAD
This rotocut attachment is designed for use with
EGO Power Head PH1400E. See " INSTALLING AN
ATTACHMENT TO THE POWER HEAD" section in the
power head PH1400E operator's manual.
OPERATION
WARNING:
to make you careless. Remember that a careless fraction of
a second is sufficient to inflict serious injury.
WARNING:
accessories not recommended by the manufacturer of
this product. The use of attachments or accessories not
recommended can result in serious personal injury.
You may use this product for the purposes listed below:
Cutting:
rails, wall edges, road curbs, fences in the running traffic, or
trimming the vegetation on parking lots.
NOTICE:
no foreign objects are thrown out which entails strong risks:
broken windows, dented car bodies, slit fences, torn tree
bark or personal injury.
USING THE ROTOCUT ATTACHMENT WITH POWER
HEAD
WARNING:
goggles or safety glasses at all times when operating this unit.
Wear a face mask or dust mask in dusty locations.
Clear the area to be cut before each use. Remove all objects,
such as rocks, broken glass, nails, wire, or line, that can be
thrown or become entangled in the cutting attachment. Clear
the area of children, bystanders, and pets. At a minimum,
keep all children, bystanders and pets at least 15m away;
there still may be risk to bystanders from thrown objects.
Bystanders should be encouraged to wear eye protection. If
Make sure the guard is fixed according to
Do not allow familiarity with this product
Do not use any attachments or
used for cutting the grass around stakes or guard
When using the rotocut attachment, ensure that
To avoid serious personal injury, wear

Publicité

Table des Matières
loading

Table des Matières