Items Supplied; General Safety Information - EINHELL AGH 18 Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 12
Anleitung AGH 18-12 sprachig

1. Items supplied

1. Cordless grass cutter
2. Hedge trimmer blade
3. Charging supply unit
4. Charging adapter
5. Case

2. General safety information

Caution! Danger!
The blade will run on for a few seconds after the
tool is switched off!
Please read the directions for use carefully and
observe the information provided. It is important to
consult these instructions in order to acquaint
yourself with the tool, its proper use and safety
precautions.
Important!
For safety reasons the cordless grass cutter and
hedge trimmer is not to be used by children,
young people under 16 years of age, or any other
persons who are not acquainted with these
directions for use.
Examine the tool each time before you use it. Do
not use the tool if any safety devices and/or
blades are damaged or worn. Never put safety
devices out of operation.
Use the tool only for the purpose specified in
these instructions.
You are responsible for safety in your work area.
Inspect the items you want to cut before starting
to work. Remove any foreign objects you find.
Watch out for foreign objects while you work. If
you still hit upon an obstacle while cutting, turn
off the tool (let go of the ON button) and remove
the obstacle.
If the blades become jammed, switch off the tool
(let go of the ON button) and remove the
obstruction (thick branch, foreign object) with a
blunt item. Never use your fingers to clear an
obstruction - the pre-loaded blades can cause
serious injury.
Examine the charging cable regularly for signs of
damage and age (brittleness). Use only if it is in
perfect condition.
Work only in good visibility.
Always make sure of your footing while working.
Be careful when stepping backwards. Risk of
stumbling!
If you interrupt your work to move to a different
position it is imperative to switch off the tool while
you are moving there.
Never use the tool in the rain or in moist or wet
conditions.
24.10.2001 9:23 Uhr
Avoid contact with leaky batteries. In case of
contact, wash the affected area of skin
immediately with water and soap. If battery acid
gets in your eye, rinse out the eye with water for
at least 1 minute and consult a doctor at once.
Protect the battery charger and cable from
damage and sharp edges. Damaged cables are
to be replaced without delay by an electrician.
Always remove the NC storage battery before
you perform any work on the tool, e.g.
- cleaning the blades
- troubleshooting
- cleaning and maintenance
or before leaving the tool unattended.
Never work with the tool in the rain and never
leave the tool outdoors. The tool must not be
used if it is wet.
We recommend that you wear safety goggles
when working with the tool.
Wear suitable working clothes such as rubber
gloves and non-slip shoes. Do not wear loose
garments. Keep long hair in a hairnet.
Avoid abnormal postures and make sure of your
footing.
Be sure to hold the tool well away from your
body when it is switched on.
Make sure there are no other persons or animals
within your working area (radius of swing).
Keep cables clear of where you are cutting.
Use the tool only when it is in good working
order.
Protect cables from heat, caustic fluids and
sharp edges. Replace damaged cables
immediately.
Examine the cutting system regularly for signs of
damage and, if necessary, arrange for the tool to
be professionally repaired by the ISC Customer
Service Center or a specialist workshop.
Keep the tool in a dry place out of children's
reach.
When the tool is not being used, store it so that
the blades cannot be touched accidentally.
Take care not to overload the tool and do not use
it on jobs for which it is not intended.
The tool requires regular inspection and
maintenance. Always replace damaged blades in
pairs. If the tool suffers any damage from impact
(falling on hard ground etc.), have it checked
immediately by a specialist.
Look after your tool carefully. Keep it clean and
sharp to ensure efficient and safe cutting. Follow
the maintenance and cleaning instructions.
Seite 9
GB
9

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

34.101.10

Table des Matières