Rechargeable Battery Pack; Optional Accessories; Protecting The Environment - DeWalt DHS780 Mode D'emploi

EnGLISH
In case of workpiece fragments jammed between the saw blade and guards, disconnect the
machine from the power supply and follow the instructions given in Changing or Installing a
New Saw Blade. Remove the jammed parts and reassemble the saw blade.
Periodically clean all dust and wood chips from around AND UNDER the base and the
rotary table.

WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear approved eye protection and approved dust
mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic
parts of the tool. These chemicals may weaken the materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.
Cleaning the D WALT Corded Power Supply
e

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic
parts of the tool. These chemicals may weaken the plastic materials used in these parts.
Use a cloth dampened only with water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Cleaning the Corded Power Supply Receptacle (Fig. D)

WARNING: Blow debris out of the corded power supply receptacle
To minimize the risk of eye injury, always wear eye protection and respiratory protection
when performing this.
Dust Duct Cleaning
Depending on your cutting environment, saw dust can clog the dust duct and may prevent
dust from flowing away from the cutting area properly. With the battery pack or corded power
supply removed and the saw head raised fully, low pressure air or a large diameter dowel rod
can be used to clear the dust out of the dust duct.
XPS™ LED Worklight Cleaning
For the best worklight performance, perform the following maintenance regularly with the
battery or corded power supply removed.
• Carefully clean saw dust and debris from worklight lens with a cotton swab.
• DO NOT use solvents of any kind, they may damage the lens.
• Dust build-up can block the worklight and prevent it from accurately indicating the line
of cut.
• Follow mitre saw's instruction manual to remove and install blade.
• With blade removed from saw, clean pitch and build-up from blade. Pitch and debris can
interfere with the worklight and prevent it from accurately indicating the line of cut.

Optional Accessories


WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only D WALT recommended accessories should be used with this product.
e
The following accessories, designed for your saw, may be helpful. In some cases, other locally
obtained work supports, length stops, clamps, etc., may be more appropriate. Use care in
selecting and using accessories.
Dust Bag: DE7053 Equipped with a zipper for
(included with some easy emptying, the dust bag
models) will capture the majority of
the sawdust produced.
SAW BLADES: ALWAYS USE 305 mm SAW BLADES WITH 25.4 mm/30 mm ARBOUR HOLES.
SPEED RATING MUST BE AT LEAST 4800 RPM. Never use a smaller diameter blade. It will
not be guarded properly. Use crosscut blades only! Do not use blades designed for ripping,
combination blades or blades with hook angles in excess of 7°.
BLADE DESCRIPTIONS
APPLICATION
construction Saw Blades (thin kerf with anti-stick rim)
General Purpose
Fine Crosscuts
Woodworking Saw Blades (provide smooth, clean cuts)
Fine crosscuts
Non-ferrous metals
Consult your dealer for further information on the appropriate accessories.

Protecting the Environment

Separate collection. Products and batteries marked with this symbol must not be
disposed of with normal household waste.
Products and batteries contain materials that can be recovered or recycled reducing
the demand for raw materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at www.2helpU.com.
42

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails to produce sufficient power on jobs
which were easily done before. At the end of its technical life, discard it with due care for our
environment:
• Run the battery pack down completely, then remove it from the tool.
• Li-Ion cells are recyclable. Take them to your dealer or a local recycling station. The
collected battery packs will be recycled or disposed of properly.
38 with clean, dry air.
WALT, have not been tested
e
DIAMETER TEETH
305 mm 40
305 mm 60
305 mm 80
305 mm 96