Quick 700 Manuel De L'utilisateur page 15

POS. DESCRIPTION
14A Electric motor 700W 12V
14B Electric motor 700W 24V
14C Electric motor 1000W 12V
14D Electric motor 1000W 24V
14E Electric motor 1400W12V
14F Electric motor 1400W 24V
15 Key
16 Gasket/Rider jig
17 Rider base
18 Sensor
19 Screw
20 Rope/chain stripper Rider base
21 Key
22 Short shaft
23 Long shaft
24 External circlip
25 Bearing
26 Internal circlip
27 Oil seal
28 Spring washer
29 Clutch cone
30 Magnet
31A Gypsy 6 mm
31B Gypsy 8 mm-5/16"
31C Gypsy 10 mm-3/8"
32 Gypsy cover
33 Drum
34 Bush
35A Handle 700-1000W
35B Handle 1400W
36 Screw for pressure lever
37A Black pressure lever
37B White pressure lever
38 Spring for gypsy pressure lever
39A Watertight 700W
39B Watertight 1000-1400W
40 Grommet 1000-1400W
41 Terminal board cover
700-1000-1400W
42 Screw
43 Bottom gasket
700-1000-1400W
44 Bottom protec cover
700-1000-1400W
45 Cable outlet
CODE
E M F 0 7 1 2 0 0 0 0 0
E M F 0 7 2 4 0 0 0 0 0
E M F 1 0 1 2 0 0 0 0 0
E M F 1 0 2 4 0 0 0 0 0
E M F 1 4 1 2 0 0 0 0 0
QUICK windlasses are manufactured with materials
E M F 1 4 2 4 0 0 0 0 0
resistant to marine environments. In any case, any salt
MBH050515F00
deposits on the outside must be removed periodically
P G B S C 1 0 0 0 0 0 0
to avoid corrosion and damage to the equipment. The
SGMSC10C0000
S A K R E E D 0 0 0 0 0
parts where salt may have built up should be washed
MBV0620MXSC0
thoroughly with fresh water.
MSN10CX00000
MBH080780F00
Once a year, the drum and the gypsy are to be taken
MSAS10274R10
apart as follows:
MSAS10308R00
DRUM VERSION
MBAE2520Y000
M B J 6 0 0 5 2 R S 1 0
Use the handle (35) to loosen the bush (34); pull off
MBAN4717Y000
the drum (33) and the top clutch cone (29); loosen the
P G P R L 2 5 4 7 7 0 0
fixing screws (2 or 19) of the rope/chain stripper (3 or
MBR254025X00
20) and remove it. Pull off the gypsy (31).
M S F 1 0 0 0 0 0 0 0 0
KPMC08060000
NO-DRUM VERSION
Z S B 1 0 0 6 0 0 0 0 0
Use the handle (35) to remove the gypsy cover (32);
Z S B 1 0 0 8 5 1 6 0 0
remove the top clutch cone (29); loosen the fixing
Z S B 1 0 1 0 3 8 0 0 0
MSGB10000R01
screws (2 or 19) of the rope/chain stripper (3 or 20)
M S E 1 0 0 0 0 0 R 0 1
and remove it and pull off the gypsy (31).
MSD100000R01
Clean all the parts removed to avoid corrosion, and
MSHD00000000
Z S L M S H 0 0 0 0 0 0
grease the shaft thread (22 or 23) and the gypsy (31)
MSMVT1000000
where the clutch cones rest (29) (use grease suitable
P D LV T D 1 0 0 0 0 0
for marine environment).
PDLVTD10W000
MMTND1000000
Periodically grease the hinge pin (5) of the inspection
MMTND1000000
door (only windlasses with aluminium bases).
PCCCPM100000
PCGPMMR00000
Remove any oxide deposits from the terminals of the
electric motor and the reversing solenoid unit; grease
PCCPPMMR0000
them.
MBV02213AXSC
PGGPMFN00000
PCCPPMFN0000
PPM20B000000
MAINTENANCE
WARNING:
make sure the electrical power to
the motor is switched off when working
manually on the windlass. Carefully remove the
chain or rope from the gypsy or the rope from
the drum.
GB
15