LaMotte WaterLink SpinTouch DW Mode D'emploi page 7

meter into an AC outlet. WARNING: only use the AC adapter supplied with this equipment. Do not
substitute.
The battery charge status is indicated by the battery icon on the display. The
battery icon will indicate when the battery charge is full, partial, low, empty or
charging. The empty battery icon will flash to indicate that meter should be
connected to AC power source. If the meter continues to be used at low battery power without
connecting it an AC power source, the meter will go into an auto-shutdown mode. In this mode
the meter will be locked until meter is connected to an AC source and the battery is charged to a
sufficient voltage. While charging, the charging battery icon will be displayed. The meter should
remain plugged in until the battery is fully charged. When the battery is completely charged, the
charging icon will change to the full battery icon.
SETTINGS
Tap to enter the SETTINGS menu. Tap
Brightness The brightness level of the display can be adjusted from 00 to 10. Tap
adjust the brightness. Tap
Date/Time The Year, Month, Day, Format, Hour, Minute, AM/PM can be set. Tap
adjust the displayed value. Tap
(minutes for 24 hour format, AM/PM for 12 hour format) tap
Tap to exit to the Settings menu at any time.
Set Language There are ten language options – English, French, Spanish, German, Dutch,
Swedish, Portuguese, Italian, Turkish, Chinese. Tap selection. Tap
Calibration Tap to run an angle calibration to evaluate the alignment of the hub and disk. Tap
to exit to the Settings menu.
Power Options There are three power options: Auto Dim Time, Auto Off Time, and Power. Tap the
options then tap a selection. Tap selection. Tap
Bluetooth There are two Bluetooth options: Bluetooth Enabled and Fast Printer Connect that are
used to print test results. Tap
Market Type Tap to select the market type. Select Drinking Water. Tap
menu.
Other Settings Units allows the selection of units for the Hardness test results to be reported as
gpg or ppm for the Drinking Water market. It also allows the selection of the Nitrate test results
to be reported as ppm Nitrate (NO
as ppm Nitrate (NO
3
reported as nitrate nitrogen NO
(NO -N).
2
About... lists the Serial Number, Firmware Version, Bluetooth MAC address, Bluetooth Version and
Test Count. The Test Count shows the number of complete tests that have been performed over
the lifetime of the meter. Tap
Ranges Enabled allows the option of having test results that are out of the range of the reagent
system displayed in red. The default setting is on.
When Show Market Type is selected, the market type will be displayed on the Testing Screen. The
default setting is OFF. Tap
RANGES
Test Factor
Alkalinity, Total
Chlorine, Free
Chlorine, Total
Combined Chlorine
Copper
Hardness, Total
Iron, Ferrous, soluble
Iron, Ferric, soluble
to exit to the Settings menu.
to move to the next value. After the last value has been chosen
to exit to the Settings menu.
) or ppm Nitrate Nitrogen (NO
3
) the nitrite results will be reported as ppm Nitrite (NO
-N) the nitrite results will be reported as ppm Nitrite Nitrogen
3
to return to the Settings menu.
to return to the Settings menu.
Range
0–250 ppm
0.00–15.00 ppm
0.00–15.00 ppm
0.00–15.00 ppm
0.0-6.0 ppm
0–70 gpg/0-1200 ppm
0.0–6.0 ppm
0.0–6.0 ppm
to return to the test screen at any time.
to return to the Settings menu.
to exit to the Settings menu.
3
7
or
to exit to the Settings menu.
to exit to the Settings
-N). When results are reported
). When results are
2
Display Abbreviation
ALK
FCL
TCL
CCL
COPPER
Hardgpg/T HARD
FERROUS
FERRIC
and to
to