BFT MOOVI 30-50 Instructions D'utilisation page 16

ENGLISH
- Set the opening microswitch (fig.12 ref. SWO) by loosening the dowel (fig.
13 ref. G) and moving the cam (fig.13 ref. C) until the microswitch trip is heard
(or checking that the respective control unit LED switches off).
- Manually bring the bar to its completely closed position resting onto the
fork (fig.11 ref. F). Check that the bar is perfectly horizontal using a level
(fig.11 ref. L).
- Set the closing microswitch (fig.12 ref. SWC) by loosening the dowel
(fig.13 ref. G) and moving the cam (fig.13 ref. C) until the microswitch trip
is heard (or check that the respective control unit LED switches off).
- Set the closing microswitch (fig.12 ref. SWC) so that the bar stops a few
millimeters before hitting the fork (fig.11 ref. F).
- Activate the motorised operation and run a few cycles.
- Check that the electrical limit switch stops the bar before it reaches its
vertical open position.
- Check that the electrical limit switch stops the bar before it reaches its
horizontal closed position on the "F" fork.
- If necessary, adjust the position of the "C" cams (fig.13) which control the
end-of-stroke devices.
11) EMERGENCY RELEASE (Fig.14)
The emergency release allows the bar to be manoeuvred manually. It is
activated from the outside of the box by inserting the personalised key into
the lock placed under the bar and rotating it anticlockwise by 180°.
WARNING! When an actuator without bar needs to be released, ensure
that the balancing spring is not compressed (bar in the opening position).
12) USE OF AUTOMATION
As automation can be remotely controlled and therefore not within sight, it
is essential to frequently check that all safety devices are perfectly efficient.
WARNING! In case of any malfunction in the safety devices, take imme-
diate action and require the assistance of a specialised technician.
It is recommended to keep children at a safe distance from the automation
field of action.
13) CONTROL
The automation system is used to obtain motorised access control. There
are different types of control (manual, remote, magnetic badge, mass
detector etc.) depending on the installation requirements and characteri-
stics. For the various control systems, see the relevant instructions.
14) MAINTENANCE
WARNING: before opening the door, make sure that the spring has
been unloaded (rod at 43
maintenance to the installation, disconnect the mains power supply. The
following points need checking and maintenance:
- Photocell optics. Clean occasionally.
- Electric edge. Carry out a periodical manual check to ensure that the edge
stops the bar in case of obstacles.
- Dismantle the gearmotor and replace the lubricating grease every two
years.
- When any operational malfunction is found, and not resolved, disconnect
the mains power supply and require the assistance of a specialised tech-
nician (installer). When automation is out of order, activate the emergency
release (see paragraph "11") so as torelease the manual bar opening and
closing operations.
15) SCRAPPING
Materials must be disposed of in conformity with the current regulations.
In case of scrapping, the automation devices do not entail any particular
risks or danger. In case of recovered materials, these should be sorted out
by type (electrical components, copper, aluminium, plastic etc.).
16) DISMANTLING
WARNING: before opening the door, make sure that the spring has
°
been unloaded (rod at 43 ). When the automation system is disassembled
to be reassembled on another site, proceed as follows:
- Disconnect the power supply and the entire electrical installation.
- Remove the actuator from its fixing base.
- Disassemble all the installation components.
- In the case where some of the components cannot be removed or are
damaged, they must be replaced.
17) MALFUNCTION: CAUSES and REMEDIES
17.1) The bar does not open. The motor does not turn.
WARNING: before opening the door, make sure that the spring has
°
been unloaded (rod at 43 ).
1) Check that the photocells are not dirty, or engaged, or not aligned. Proceed
accordingly. Check the electric edge.
2) If the engine is overheated, the thermal protection might have been acti-
16
- MOOVI 30-50 Ver. 04
INSTALLATION MANUAL
°
). WARNING: Before carrying out any
vated. Wait for it to be reset.
3) Check the correct connection of the drive motor and capacitor.
4) Check that the electronic appliance is correctly supplied. Check the integrity
of the fuses.
5) Check that the functions are correct by means of the control unit dia-
gnosing LEDs (see relevant instructions). Identify causes for faults, if any.
If the LEDs show persisting start control, check that no radio controls, start
buttons or other control devices keep the start contact activated (closed).
6) If the control unit does not work, it must be replaced.
7) Check the movement of the cam-holder bars (fig. 13), if it is not smooth,
the bars must be lubricated.
17.2) The bar does not open. The motor turns but there is no movement.
1) The manual release was left engaged. Reset the motorised operation.
2) If the release is in the motorised operation position, check the gearmo- tor
for integrity.
WARNINGS
Correct controller operation is only ensured when the data contained
in the present manual are observed. The company is not to be held
responsible for any damage resulting from failure to observe the
installation standards and the instructions contained in the
present manual.
The descriptions and illustrations contained in the present manual
are not binding. The Company reserves the right to make any alterations
deemed appropriate for the technical, manufacturing and commercial
improvement of the product, while leaving the essential product
features unchanged, at any time and without undertaking to update
the present publication.