Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
O
E
PTIONAL
QUIPMENT
Optional Equipment Connections
Note:
The remote control must be programmed with supplied
codes to operate the optional equipment.
VCR Connection
VCRs, video disc players, video game equipment, and
DSS equipment can also be connected to the video inputs.
See the optional equipment manual for more information.
Note:
VIDEO 1 input is a dual-purpose input. It is primarily
intended for connection with 480i devices such as a DVD
player using the Y P
Audio L & R jacks. However, it can also be connected to
conventional composite video sources such as a VCR,
using only the Y/Video jack and Audio L & R jacks. The
on-screen label will display Component or Video 1
depending on which source is connected.
TERMINALS ON BACK OF TELEVISION
INPUT 1
R-AUDIO-L
COMPONENT
TO AUDIO
VIDEO INPUT
AMP
P
P
R
B
ANT
L
INPUT 2
S-VIDEO
R
R-AUDIO-L VIDEO
Use either the S-Video or
Video Connection
CABLES NOT INCLUDED
Note:
Rear A/V jacks diagram may vary, depending on model.
Please refer to the FEATURE CHART on page 3 for your
model's capabilities.
Procedure
•
Connect equipment as shown to front or rear Audio/
Video input jacks.
•
Select the Video mode by pressing TV/VIDEO button.
•
Operate optional equipment as instructed in equipment
manual.
Note:
Do not connect S-VIDEO and VIDEO signal to INPUT 2 at the
same time. If both are connected, signal interference will result.
Use either the S-VIDEO or the Video signal only (models CT-
20SL14, CT-24SL14, CT-27SC14 and CT-27SL14 only).
Front Control Panel
The front control panel can be used to access menus and
switch video mode when the remote control is not
available.
Front panel for CT-32SL14/CT-36SL14
CH
POWER
VOL
CH
ON/OFF INDICATOR
POWER ON/OFF
Note: Model CT-27SC14 does not have
ON/OFF Indicator.
POWER
VOLUME
CHANNEL
Front panel for CT-27SC14/CT-32SC14 (may vary depending on model)
Note:
The ON/OFF indicator LED (red) will light up (red) when
the set is on.
6
C
ONNECTIONS
P
component video jacks and
B
R
VCR
PLAY
R
FF
E
W
STOP
VIDEO OUT
L
Y/VIDEO
AUDIO OUT
R
ANT OUT
ANT IN
Incoming
Cable
HPJ
VIDEO 3 L AUDIO IN R
Jack used
FRONT A/V JACKS
for 1/8"
headphone plug
VOL
TV / VIDEO
S-VIDEO
VIDEO
L - AUDIO - R
INPUT 3
ACTION TV/VIDEO
HPJ
S-VIDEO VIDEO L - AUDIO - R
Procedure
•
Connect equipment to front Audio/Video input jacks.
•
Press TV/VIDEO button to select desired input mode.
•
Operate optional equipment as instructed in equipment
manual.
Note:
Front A/V jacks diagram may vary, depending on model.
Please refer to the FEATURE CHART on page 3 for your
model's capabilities.
Cable Box Connection
Follow this diagram when connecting your television to a
Cable Box.
CABLE BOX
15
ANT IN
ANT OUT
Incoming
Cable
Procedure
•
Tune the television to channel 3 or 4 depending on the
RF out setting of the cable box.
•
Using the cable box, tune to the premium cable channel
you want to view.
Digital TV - Set-Top Box (DTV-STB) or DVD
Player Connection
Use this diagram to connect the Panasonic DTV-STB
(Digital TV-Set-Top Box) to the back of your TV.
Note:
Rear A/V jacks diagram may vary, depending on model.
Please refer to the FEATURE CHART on page 3 for your
model's capabilities.
CABLES NOT SUPPLIED
TERMINALS ON BACK OF
DTV-STB OR DVD PLAYER
DIGITAL TV OUTPUT
Y
P
R-AUDIO-L
B
R-AUDIO-L
NTSC OUTPUT
Notes:
•
There are three video jacks, Y, P
Separate
HPJ
luminance and color separation. Use the L (left)
and R (right) audio inputs.
•
Select DTV-STB to 480i output mode. TV set can
receive 480i signal only. Picture distortion will result
INPUT 3
if any other type of format is selected (i.e. 480p,
720p or 1080i).
TERMINALS ON BACK OF TELEVISION
INPUT 1
COMPONENT
TO AUDIO
VIDEO INPUT
AMP
ANT
L
INPUT 2
S-VIDEO
R
CABLES NOT INCLUDED
COMPONENT VIDEO INPUT
TERMINALS ON BACK OF TV
INPUT 1
COMPONENT
TO AUDIO
VIDEO INPUT
AMP
P
R
L
INPUT 2
S-VIDEO
VIDEO
S-VIDEO
R
component
color
R-AUDIO-L
P
P
Y/VIDEO
R
B
R-AUDIO-L VIDEO
R-AUDIO-L
P
P
Y/VIDEO
R
B
R-AUDIO-L VIDEO
, and P
.
B
R
inputs
provide
Publicité
Chapitres
Table des Matières
Dépannage
