Starting Up; Replacing The Power Cable - EINHELL BT-MG 180/1 Mode D'emploi

Anleitung_BT_MG_180_1_SPK1:_
GB
5.1 Fitting the plug-in tools (Figures 1/2/3)
To fit the plug-in tools safely you should hold the
multifunction tool so that the ON/OFF switch (1)
points down and the tool mounting (2) faces up.
Place the plug-in tool (e.g. the triangular
sanding/grinding plant) on the tool mounting (2)
so that the pins of the tool mounting (2) fit into the
recesses in the plug-in tool.
Secure the plug-in tool using the supplied screw
(b) and tighten the screw securely with the Allen
key (9).
Make sure that the washer (a) is used for the
screw (b) only in connection with the saw blade
and the scraper (see Figure 3). In this case the
corrugated face of the washer must be placed
against the plug-in tool.
Check that the plug-in tool is secure.
5.2 Triangular sanding/grinding plate
Fit the triangular sanding/grinding plate to use the
equipment as a delta sander/grinder.
5.2.1 Fastening the sanding/grinding paper
The Velcro fastener enables easy changing of
sanding/grinding paper. Make sure that the vacuum
extraction holes on the sanding/grinding paper and
the sanding/grinding disk are aligned.
5.3 Fitting the dust extraction device (Fig. 4/5)
The dust extraction system prevents the
accumulation of dirt and high dust loads in the air,
and it makes it easier to dispose of the dust.
Place the equipment in a stable position as
shown in 5.1.
Fit the dust extraction device (4) with the tool
mounting (2) positioned as shown in Figure 4.
Use the Allen key (5) to secure the screws (c) in
the holes provided.
Connect the extractor adapter (3) to the dust
extraction device (4). Make sure that the arrow
(a) on the extractor device coincides with the
recess (b) on the dust extraction device (4) (see
Fig. 5). Turn the extractor adapter (3) anti-
clockwise until it engages..
Connect your tool to an extraction unit or vacuum
cleaner. This will provide excellent extraction of
chips and dust from the workpiece.
The benefits are that you will protect both the
equipment and your own health. Your work area will
also be clean and safe.
12
16.03.2009 9:20 Uhr Seite 12
6. Starting up (Fig. 6)
6.1 Switching on/off
Slide the switch (1) forwards to switch on the
equipment.
6.2 Practical tips
Switch on the equipment.
Work away from the body.
Never move your hands into the direct vicinity of
the work area.
Use only plug-in tools which are in good working
order and undamaged.
6.2.1 Plug-in tools
Sawing: Sawing wood and plastic.
Notes on working practice: When sawing, watch out
for foreign bodies in the workpiece and remove these
if necessary. Plunge cutting is allowed only in soft
materials such as wood or plasterboard.
Sanding/grinding: Surface sanding/grinding at
edges, in corners or hard-to-reach areas. Depending
on choice of sanding/grinding paper for the
sanding/grinding of wood, paint, lacquer, etc.
Notes on working practice: This equipment offers
particularly high performance for the sanding/grinding
of hard-to-reach corners and edges. To sand/grind
profiles and channels you can also work with just the
tip or the edge of the sanding/grinding disk. Various
sanding/grinding papers are available, specially
designed for the different types of material you may
be working on and the amount you wish to remove
from the surface. The amount removed will depend
largely on the choice of sanding/grinding paper and
pressure applied to the sanding/grinding disk.
Scraping: Scraping off old paint or adhesives.
Notes on working practice: Move the plug-in tool
against the area you want to remove. Begin with a flat
angle of incidence and little pressure. The surface
(e.g. wood, plaster) may be damaged if too much
pressure is used.

7. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.