Bottom Panel; Setting Up; Placing The Receiver; Rack Mounting A Single Receiver - AKG WMS 4000 Mode D'emploi

2 Description

2.7 Bottom Panel

3 Setting Up

Important!
Important!

3.1 Placing the Receiver

3.2 Rack Mounting a Single
Receiver
Refer to fig. 3.
3.3 Rack Mounting Two
Receivers Side by Side
Refer to fig. 4.
3.4 Connecting the Receiver
to a Mixer
Refer to figs. 2 and 5.
3.5 Connecting the Receiver
to Power
Refer to fig. 6.
26
The receiver type plate
to the bottom panel.
Prior to setting up the receiver, check that the AC mains voltage stated on the supplied power sup-
ply is identical to the AC mains voltage available where you will use your system. Using the power
supply with a different AC voltage may cause damage to the unit.
Prior to setting up your WMS 4000, check that the transmitter and receiver are tuned to the same
frequency. Refer to sections 3.8.1 through 4 and the transmitter manual(s).
Note:
In the display illustrations in the following sections, flashing characters are identified by angle symbols
">" and "<". All the values shown are examples of possible settings.
Reflections off metal parts, walls, ceilings, etc. or the shadow effects of musicians and other people may
weaken or cancel the direct transmitter signal.
For best results, place the receiver or remote antennas as follows:
1. Place the receiver/antennas near the performance area (stage). Make sure, though, that the transmit-
ter will never get any closer to the receiver than 10 ft (3 m). Optimum separation is 16 ft. (5 m).
2. Check that you can see the receiver from where you will be using the transmitter.
3. Place the receiver at least 5 ft. (1.5 m) away from any big metal objects, walls, scaffolding, ceilings,
etc.
Note:
You can either use the receiver freestanding or mount it in a 19" rack using the supplied RMU 4000
rack mounting kit.
1. Unscrew the four rubber feet
2. Unscrew the two fixing screws
3. Use the fixing screws
the other side panel. The brackets are contained in the RMU 40/div. rack mounting kit.
4. Install the receiver in your rack.
To mount two receivers side by side in the same rack slot, you will need two optional RMU 40/div. rack
mounting kits.
1. Unscrew the four rubber feet
the rubber feet
2. Unscrew the two fixing screws
hand side panel of the other receiver.
3. Remove the plastic covers
4. Insert one connecting strip
align the hole in each connecting strip
panel.
5. Fix the three connecting strips
the rubber feet.
6. To join the two receivers, slide the connecting strips
the side panel of the second receiver. Make sure to align the hole in each connecting strip
appropriate threaded hole in the bottom panel of the second receiver.
7. Fix the connecting strips
rubber feet.
8. Screw a short bracket
screws you removed from the receiver side panels.
9. Install the receivers in your rack.
Note:
Be sure to keep the remaining screws
Connect the audio output to the desired input:
- BALANCED socket
- BALANCED socket
- UNBALANCED jack
1. Check that the AC mains voltage stated on the supplied power supply is identical to the AC
mains voltage available where you will use your system. Using the power supply with a differ-
ent AC voltage may cause damage to the unit.
2. Plug the feeder cable
rear panel and screw down the DC connector
3. Plug the power cable on the power supply into a convenient power outlet.
indicating available carrier frequency ranges and approval information is affixed
from the receiver bottom panel.
from each side panel.
to screw the short bracket
from each receiver's bottom panel and remove the screws
.
from the right-hand side panel of one receiver and from the left-
from the side panels with the fixing screws
into each free slot in the side panel of the first receiver, making sure to
with the appropriate threaded hole in the receiver bottom
on the first receiver using three of the screws
on the second receiver using the three screws
to the outer side panel of each receiver using for each bracket two of the
for later use.
- XLR cable - microphone input: set output level switch µ to "-30 dB".
- XLR cable - line input: set output level switch µ to "0 dB" or "+6 dB".
- 1/4" jack cable - unbalanced 1/4" microphone or line input jack.
on the supplied power supply into the DC ONLY socket
to one side panel and the long bracket
still on.
on the first receiver through the free slots in
.
to
from
you removed from
with the
you removed from the
on the receiver