Dust Collection; Removing/Inserting The Battery - Milwaukee 2739-20 Manuel De L'utilisateur

Mounting the Miter Saw
To prevent the tool from sliding, falling or tipping
from a raised work surface during operation, the saw
should be mounted to a supporting surface such as
a level, sturdy work table, bench, or miter saw stand.
Position the saw and workbench to allow adequate
room for cross-cutting long workpieces. To mount
the saw to a flat surface, insert fasteners through
the holes in the corners of the saw base and secure.
Follow manufacturer instructions when mounting to
a miter saw stand.

Dust collection

Collected sawdust from coated
WARNING
(polyurethanes, linseed oil, etc.)
workpieces can self-ignite in the dust bag or
elsewhere and cause fire. To reduce the risk of
fire, empty the dust bag frequently and never
store or leave a saw without totally emptying its
dust bag.
The dust port at the back of the saw can be con-
nected to a standard workshop vacuum hose or the
included dust bag. Leave the dust bag open to direct
dust down into a garbage can.
To install, push and twist the hose or dust bag onto
the dust port.
Using Face Boards
When using face boards, secure them using the
mounting holes in the fences. Face boards place dis-
tance between the fence and the workpiece, providing
improved support for some workpieces. Workpiece
splintering can be reduced by using face boards.
Selecting, Installing, and Changing Blades
Always use clean, sharp blades. Dull blades tend to
overload the tool, bind, and cause pinching. Use only
12" sliding miter saw blades rated at least 5000 RPM.
1. Remove battery pack.
2. Lower the saw head.
3. Raise the lower guard and hold up while raising
the saw head. Let go of the lower guard. The lower
guard will remain up in the blade-changing OPEN
position. WARNING! Be careful not to lower the
guard head while changing the blade; the lower
guard will fall back into place to cover the blade
and could pinch hands and fingers.
4. Press in the spindle lock and rotate the spindle/
blade until the lock engages.
5. Use the wrench to loosen and remove the left-hand
thread blade bolt (clockwise).
6. Remove the outer blade flange and blade. Wipe
the flanges and spindle to remove dust and debris.
Inspect the parts for damage. Replace if needed.
7. Match the arrow direction on the blade with the
arrow direction on the lower guard. Slide the blade
onto the spindle.
8. Install the outer blade flange. The flat side of the
flange must rest against the blade.
9. Press in the spindle lock and rotate the blade until
the lock engages. Insert and securely tighten the
blade bolt (counterclockwise) with the wrench.
10. Move hands out of the guard area and lower
11. Check the clearance between the blade, kerf
WARNING
cific charging instructions, read the operator's
manual supplied with your charger and battery.
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
may be hazardous.
Guard in
blade-changing
To learn more about the ONE-KEY™ function-
OPEN position
ality for this tool, please reference the Quick
Start guide included with this product or go to
milwaukeetool.com/One-Key. To download the
ONE-KEY™ app, visit the App Store or Google Play
from your smart device.
Solid Blue
Outer flange
Blinking Blue Tool is actively communicating with
Blade
Blinking Red Tool is in security lockout and can
Blade bolt
6
the saw head. The lower guard will fall back into
place; verify it moves freely.
plate, and fences. Always use the kerf plate. Kerf
plates reduce tear-out and splintering along the
cut by providing edge support.
Recharge only with the charger
specified for the battery. For spe-

Removing/Inserting the Battery

Always remove battery pack before
changing or removing accessories.
Only use accessories specifically
recommended for this tool. Others
ONE-KEY™
ONE-KEY™ Indicator
Wireless mode is active and ready
to be configured via the ONE-KEY™
app.
the ONE-KEY™ app.
be unlocked by the owner via the
ONE-KEY™ app.