Bosch GCM 10 GDJ Professional Notice Originale page 33

If the workpiece or blade becomes jammed, turn the
u
mitre saw off. Wait for all moving parts to stop and
disconnect the plug from the power source and/or re-
move the battery pack. Then work to free the jammed
material. Continued sawing with a jammed workpiece
could cause loss of control or damage to the mitre saw.
After finishing the cut, release the switch, hold the
u
saw head down and wait for the blade to stop before
removing the cut-off piece. Reaching with your hand
near the coasting blade is dangerous.
Hold the handle firmly when making an incomplete cut
u
or when releasing the switch before the saw head is
completely in the down position. The braking action of
the saw may cause the saw head to be suddenly pulled
downward, causing a risk of injury.
Keep your work area clean. Material mixtures are partic-
u
ularly hazardous. Light metal dust may catch fire or ex-
plode.
Do not use dull, cracked, bent or damaged saw blades.
u
Unsharpened or improperly set saw blades produce
narrow kerf causing excessive friction, blade binding
and kickback.
Do not use saw blades made from high speed steel
u
(HSS). Such saw blades can easily break.
Always use saw blades with correct size and shape
u
(diamond versus round) of arbour holes. Saw blades
that do not match the mounting hardware of the saw will
run off-centre, causing loss of control.
Never remove cuttings, wood chips, etc. from the cut-
u
ting area while the power tool is running. Always guide
the tool arm back to the neutral position first and then
switch the power tool off.
Do not touch the saw blade after working before it has
u
cooled. The saw blade becomes very hot while working.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Symbols
The following symbols may be important for the operation of
your power tool. Please take note of these symbols and their
meaning. Correctly interpreting the symbols will help you to
operate the power tool more effectively and safely.
Bosch Power Tools
Symbols and their meaning
Keep hands away from the cutting
area while the power tool is running.
Contact with the saw blade can lead to
injuries.
Wear a dust mask.
Wear safety goggles.
Wear hearing protection. Exposure
to noise can cause hearing loss.
Danger area! Keep hands, fingers
and arms away from this area.
Keep your fingers away from the
moving parts of the glide arm. There
is a risk of fingers being crushed and
severely injured.
3 601 M27 04. Take note of the dimensions of the saw
blade. The hole diameter must fit the
3 601 M27 0L.
tool spindle without play. If it is neces-
3 601 M27 08.
sary to use reducers, ensure that the
3 601 M27 0B.
dimensions of the reducer are suitable
3 601 M27 0K.
for the base blade thickness and the
saw blade hole diameter, as well as the
tool spindle diameter. Wherever pos-
3 601 M27 00.
sible, use the reducers provided with
3 601 M27 03.
the saw blade.
3 601 M27 06.
The saw blade diameter must match
3 601 M27 07.
the information specified on the sym-
bol.
30mm
When transporting the power tool,
hold it only at the locations (recessed
handles) indicated.
Never carry the power tool using the
handle of the glide arm.
English | 33
1 609 92A 5U5 | (01.10.2020)