Milwaukee M18 FMTIW2P12 Notice Originale page 9

TECHNICAL DATA CORDLESS IMPACT SCREWDRIVER
Production code.....................................................................
No-load speed ................................................
Impact range ..................................................
Torque ............................................................
No-load speed ................................................
Impact range ..................................................
Torque ............................................................
No-load speed ................................................
Impact range ..................................................
Torque ............................................................
No-load speed ................................................
Impact range ..................................................
Torque ............................................................
Torque max. ...........................................................................
Max. diameter bolt / nut .........................................................
Tool reception ........................................................................
Battery voltage.......................................................................
Weight according EPTA-Procedure 01/2014 (2.0 ... 12.0 Ah)
Recommended ambient operating temperature ....................
Recommended battery types.................................................
Recommended charger .........................................................
Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ......................
Sound power level (Uncertainty K=3dB(A)) ...........................
Wear ear protectors!
Total vibration values (vector sum in the three axes)
determined according to EN 62841.
Vibration emission value a
h
Impact tightening of fasteners of the maximum capacity of the tool
Uncertainty K= ....................................................................
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized
test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of
exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for
diff erent applications, with diff erent accessories or poorly maintained, the vibration and noise emission may diff er. This may
signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is
switched off or when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the
total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the
tool and the accessories, keep the hands warm, organization of work patterns.
WARNING Read all safety warnings, instructions,
illustrations and specifi cations provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
IMPACT SCREWDRIVER SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces,
when performing an operation where the fastener may
contact hidden wiring. Fasteners contacting a „live" wire
may make exposed metal parts of the power tool „live" and
could give the operator an electric shock.
Wear ear protectors. Exposure to noise can cause
hearing loss.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses
when working with the machine. The use of protective
clothing is recommended, such as dust mask, protective
gloves, sturdy non-slip footwear, helmet and ear defenders.
16 ENGLISH
M18 FMTIW2P12 M18 FMTIW2P12 M18 FMTIW2F12 M18 FMTIW2F12 M18 FMTIW2F38 M18 FMTIW2F38
.... 4777 19 01... .... 4777 19 01... 4777 08 01... 4777 08 01... 4836 03 01 4836 03 01
...000001-999999 ...000001-999999 ...000001-999999 ...000001-999999 ...000001-999999 ...000001-999999
..... 0-1250 min ..... 0-1250 min -1 -1 .............. 0-1250 min .............. 0-1250 min -1 -1 ............ 0-1250 min ............ 0-1250 min
....... 0-900 min ....... 0-900 min -1 -1 ................ 0-900 min ................ 0-900 min -1 -1 .............. 0-900 min .............. 0-900 min
....... 0-475 Nm .................. 0-475 Nm ................ 0-271 Nm ....... 0-475 Nm .................. 0-475 Nm ................ 0-271 Nm
..... 0-1950 min ..... 0-1950 min -1 -1 .............. 0-1950 min .............. 0-1950 min -1 -1 ............ 0-1950 min ............ 0-1950 min
..... 0-2100 min ..... 0-2100 min -1 -1 .............. 0-2100 min .............. 0-2100 min -1 -1 ............ 0-2100 min ............ 0-2100 min
....... 0-610 Nm .................. 0-610 Nm ................ 0-406 Nm ....... 0-610 Nm .................. 0-610 Nm ................ 0-406 Nm
..... 0-2575 min ..... 0-2575 min -1 -1 .............. 0-2575 min .............. 0-2575 min -1 -1 ............ 0-2575 min ............ 0-2575 min
..... 0-3100 min ..... 0-3100 min -1 -1 .............. 0-3100 min .............. 0-3100 min -1 -1 ............ 0-3100 min ............ 0-3100 min
....... 0-745 Nm .................. 0-745 Nm ................ 0-745 Nm ....... 0-745 Nm .................. 0-745 Nm ................ 0-745 Nm
..... 0-1325 min ..... 0-1325 min .............. 0-1325 min .............. 0-1325 min ............ 0-1325 min ............ 0-1325 min
-1 -1 -1 -1
............... - ................................ - .............................. - ............... - ................................ - .............................. -
.............47 Nm ........................47 Nm ..................... 47 Nm .............47 Nm ........................47 Nm ..................... 47 Nm
...........745 Nm ......................745 Nm ................... 745 Nm ...........745 Nm ......................745 Nm ................... 745 Nm
..........M22 ...........................M22 ........................ M22 ..........M22 ...........................M22 ........................ M22
. 1/2" (12,7 mm) ........... 1/2" (12,7 mm) .......... 3/8" (9,5 mm) . 1/2" (12,7 mm) ........... 1/2" (12,7 mm) .......... 3/8" (9,5 mm)
.............18 V ............................18 V ........................ 18 V .............18 V ............................18 V ........................ 18 V
..2,0 ... 3,1 kg ...............2,0 ... 3,1 kg ............ 2,0 ... 3,1 kg ..2,0 ... 3,1 kg ...............2,0 ... 3,1 kg ............ 2,0 ... 3,1 kg
............................................-18...+50 °C ............................................-18...+50 °C
................................... M18B..., M18HB... ................................... M18B..., M18HB...
..................................M12-18..., M1418C6 ..................................M12-18..., M1418C6
..........95,4 dB (A) .................95,4 dB (A) ............. 95,4 dB (A) ..........95,4 dB (A) .................95,4 dB (A) ............. 95,4 dB (A)
........106,4 dB (A) ...............106,4 dB (A) ........... 106,4 dB (A) ........106,4 dB (A) ...............106,4 dB (A) ........... 106,4 dB (A)
..........17,3 m/s ..........17,3 m/s 2 2 ....................17,4 m/s ....................17,4 m/s 2 2 ................. 17,4 m/s ................. 17,4 m/s
............1,5 m/s ............1,5 m/s 2 2 ......................1,5 m/s ......................1,5 m/s 2 2 ................... 1,5 m/s ................... 1,5 m/s
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust
protection mask.
Do not machine any materials that present a danger to
health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls!
Do not switch the device on again while the insertion tool is
stalled, as doing so could trigger a sudden recoil with a
high reactive force. Determine why the insertion tool stalled
and rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the
machine is running.
When working in walls ceiling, or fl oor, take care to avoid
electric cables and gas or waterpipes.
-1 -1
-1 -1
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
-1 -1 Remove the battery pack before starting any work on the
-1 -1 machine.
Do not dispose of used battery packs in the household
refuse or by burning them. Milwaukee Distributors off er to
-1 -1
retrieve old batteries to protect our environment.
-1 -1
Do not store the battery pack together with metal objects
(short circuit risk).
-1 -1
Use only System M18 chargers for charging System M18
battery packs. Do not use battery packs from other
systems.
Never break open battery packs and chargers and store
only in dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under
extreme load or extreme temperatures. In case of contact
with battery acid wash it off immediately with soap and
water. In case of eye contact rinse thoroughly for at least
10 minutes and immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and
product damage due to a short circuit, never immerse your
tool, battery pack or charger in fl uid or allow a fl uid to fl ow
inside them. Corrosive or conductive fl uids, such as
seawater, certain industrial chemicals, and bleach or
bleach containing products, etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The cordless impact wrench can be used to tighten and
loosen nuts and bolts wherever no mains connection is
2 2
available.
2 2
Do not use this product in any other way as stated for
normal use.
RPM SETTING
The function is designed to give the user greater control
in application and reduce damage to the fastener or work
surface by automatically shutting the tool off after the tool
senses the mechanism impacting for approximately one
second.
EC DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole
responsibility that the product described under "Technical
Data" fulfi lls all the relevant regulations and the directives
2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC, and the
following harmonized standards have been used:
EN 62841-1:2015
EN 62841-2-2:2014
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 63000:2018
Winnenden, 2021-05-27
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole
responsibility that the product described under "Technical
Data" fulfi lls all the relevant provisions of the following
Regulations S.I. 2008/1597 (as amended), S.I. 2016/1091
(as amended), S.I. 2012/3032 (as amended) and that the
following designated standards have been used:
BS EN 62841-1:2015
BS EN 62841-2-2:2014
BS EN IEC 55014-1:2021
BS EN IEC 55014-2:2021
BS EN IEC 63000:2018
Winnenden, 2021-05-27
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
OPERATION
Note: It is recommended after fastening to always
check the torque with a torque wrench.
The fastening torque is aff ected by a wide variety of factors
including the following.
• State of battery charge – When the battery is discharged
voltage will drop and the fastening torque will be reduced.
• Operation at speeds – Operating the tool at low speeds
will cause a reduction in fastening torques.
• Fastening position – Holding the tool or the driving
fastener in various angles will aff ect the torque.
• Drive accessory/socket – Failure to use the correct size
accessory or socket, or a non-impact rated accessory
may cause a reduction in the fastening torque.
• Use of accessories and extensions – Depending on the
accessory or extension fi tment can reduce the fastening
force of the impact wrench.
• Bolt/Nut – Fastening torques may diff er according to the
diameter of the nut or bolt, the class of nut/bolt and the
length of nut/bolt.
• Condition of the fastener – Contaminated, corroded, dry
or lubricated fasteners may vary the fastening torques.
• Condition and base material – The base material of the
fastener and any component in between the surfaces
may eff ect the fastening torque (dry or lubricated base,
soft or hard base, disc, seal or washer between fastener
and base material).
IMPACTING TECHNIQUES
The longer a bolt, screw, or nut is impacted, the tighter it
will become.
To help prevent damaging the fasteners or workpieces,
avoid excessive impacting.
Be particularly careful when impacting smaller fasteners
because they require less impacting to reach optimum
torque.
Practice with various fasteners, noting the length of time
required to reach the desired torque.
Check the tightness with a hand-torque wrench.
If the fasteners are too tight, reduce the impacting time.
If they are not tight enough, increase the impacting time.
Oil, dirt, rust or other matter on the threads or under the
head of the fastener aff ects the degree of tightness.
ENGLISH 17