Publicité
Les langues disponibles
Les langues disponibles
Specifi cations
Cat. No.
Volts DC
No Load RPM
0602-20
12
Low 0 - 400
High 0 - 1400
0612-20
14.4
Low 0 - 400
High 0 - 1400
High Speed
Flat Bit in
Hole Saw
Cat. No.
Steel
Wood
in Wood
0602-20
3/8"
7/8"
1-1/4"
0612-20
1/2"
1"
1-3/4"
WARNING
Recharge only with the
charger specifi ed for the battery. For specifi c
charging instructions, read the operator's
manual supplied with your charger and
battery.
WARNING
Always lock trigger or
remove battery pack before changing or re-
moving accessories. Only use accessories
specifi cally recommended for this tool. Others
may be hazardous.
Inserting Battery Pack onto Tool
Battery pack can be inserted onto the tool in two
ways.
1. For working in restricted spaces, insert the bat-
tery pack from the front by sliding battery pack
onto the body of the tool. Insert the battery pack
until the battery latches lock.
2. For optimum weight distribution and balance,
insert the battery pack from the back by sliding
the battery pack onto the body of the tool. Insert
the battery pack until the battery latches lock.
3. To remove the battery pack, press in both bat-
tery latches and slide the battery pack off of the
tool.
Clip-Lok
TM
System
The Clip-Lok system consists of three pieces; the
belt clip, the tool holder, and the bit holder. The
system is shipped assembled for right-handed use.
To change the assembly for left-handed use:
Symbology
Direct Current
No Load Revolutions per
Minute (RPM)
Underwriters Laboratories, Inc.
United States and Canada
Capacities
Low Speed
Pathfi nder
Auger Bit
Screws (dia.)
Steel
Bit
in Wood
in Wood
3/8"
7/8"
1"
1/2"
1-1/4"
1-1/8"
ASSEMBLY
Bit
Fig. 1
holder
Tool
holder
Front tangs
Stud
Pin
Tool release lever
1. Remove battery pack.
2. Remove screws holding the tool holder and the
bit holder.
3. Lift the holders at the narrow end and pull the
front tangs out of their slots.
4. Replace the pieces onto the desired side by slid-
ing the tangs into the slots. Tighten the screws
securely.
4
Attaching the Belt Clip
The belt clip can be mounted to tool belts, bags,
buckets, etc. To mount the belt clip:
1. Pull up the clamp release. The clamp will pop
out.
2. Slide the clamp over the tool belt, bag, bucket,
etc.
3. Press in the clamp to tighten.
1/4"
WARNING
1/4"
pack before changing or removing acces-
sories. Only use accessories specifically
recommended for this tool. Others may be
hazardous.
WARNING
wear safety goggles or glasses with side
shields.
Using Keyless Chucks
Clamp
Your cordless tool is equipped with a spindle lock
release
that allows the chuck to be tightened with one
Belt clip
hand.
Always remove the battery pack or lock the trigger
before inserting or removing bits.
1. To open the chuck jaws,
Clamp
turn the sleeve in the
"OPEN" direction indi-
cated on the chuck.
When using drill bits,
allow the bit to strike
the bottom of the chuck.
Center the bit in the chuck jaws and lift it about
1/16" off of the bottom. When using screwdriver
bits, insert the bit far enough for the chuck jaws
to grip the hex of the bit.
2. To close the chuck jaws, turn the sleeve in the
"CLOSE" direction indicated on the chuck. The
bit is secure when the chuck makes a ratcheting
sound and the sleeve can not be rotated any
further.
NOTE: A ratcheting sound may be heard when the
chuck is opened or closed. This noise is part of the
locking feature, and does not indicate a problem
with the chuck's operation.
Using the Clip-Lok Tool Holder
1. To attach the tool to the belt clip, slide the tool
holder over the stud on the belt clip until it is
held in place by the protruding pin.
2. To release the tool from the belt clip, grasp the
tool handle, push down on the tool release lever
with your thumb, and pull up on the tool.
Using the Clip-Lok Bit Holder
The bit holder holds two standard 1/4" hex shank
bits up to two inches long.
1. Insert the bit by pressing it into the clip.
2. Remove the bit by lifting the tip of the bit and
pulling it out of the clip.
OPERATION
Using Clutch
Always remove battery
This tool has an adjustable clutch for driving differ-
ent types of screws into different materials. When
properly adjusted, the clutch will slip at a preset
torque to prevent driving the screw too deep and
to prevent damage to the screw or tool.
To adjust the clutch, turn the torque selector collar
To reduce the risk of injury,
to one of the twenty positions shown on the collar.
The number must line up with the arrow on top of
the tool.
Fig. 3 Torque selector
Fig. 2
Sleeve
Open
The torque specifi cations shown here are approximate
values obtained with a fully charged battery pack.
Positions
Close
1 - 5
6 - 10
11 - 15
16 - 20
Drill
Low
High
NOTE: Because the above settings are only a
guide, use a piece of scrap material to test the dif-
ferent clutch positions before driving screws into
the workpiece.
5
Position numbers
collar
0612-20
0602-20
Torque
Torque
0 - 10 in. lbs.
0 - 10 in. lbs.
12 - 21 in. lbs.
12 - 21 in. lbs.
24 - 32 in. lbs.
24 - 32 in. lbs.
35 - 44 in. lbs.
35 - 44 in. lbs.
280 in. lbs.
390 in. lbs
80 in. lbs.
100 in. lbs.
Publicité
