Ryobi LCD1402 Manuel D'utilisation page 5

GB
FR DE ES
DRILL SAFETY WARNINGS
Hold power tool by insulated gripping surfaces
Q
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
Know your power tool. Read operator's manual
Q
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to this
power tool. Following this rule will reduce the risk of
electric shock, fire, or serious injury.
Always wear safety glasses with side shields.
Q
Everyday glasses have only impact resistant lenses.
They are NOT safety glasses. Following this rule will
reduce the risk of eye injury.
Protect your lungs. Wear a face or dust mask if the
Q
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
Protect your hearing. Wear hearing protection
Q
during extended periods of operation. Following
this rule will reduce the risk of serious personal injury.
Battery tools do not have to be plugged into an
Q
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changing
accessories. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
Do not place battery tools or their batteries near
Q
fire or heat. This will reduce the risk of explosion and
possibly injury.
Do not crush, drop or damage battery pack. Do
Q
not use a battery pack or charger that has been
dropped or received a sharp blow. A damaged
battery is subject to explosion. Properly dispose of a
dropped or damaged battery immediately.
Batteries can explode in the presence of a source
Q
of ignition, such as a pilot light. To reduce the risk
of serious personal injury, never use any cordless
product in the presence of open flame. An exploded
battery can propel debris and chemicals. If exposed,
flush with water immediately.
Do not charge battery tool in a damp or wet
Q
location. Following this rule will reduce the risk of
electric shock.
For best results, your battery tool should be
Q
charged in a location where the temperature is
more than 10°C but less than 37.78°C. To reduce
the risk of serious personal injury, do not store outside
or in vehicles.
Under extreme usage or temperature conditions,
Q
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
IT NL PT DK SE FI NO RU PL CZ
English
or vinegar. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
Save these instructions. Refer to them frequently
Q
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them these
instructions also to prevent misuse of the product and
possible injury.
DESCRIPTION
1. Keyless Chuck
2. Switch Trigger
3. Rotation Selector (Forward/reverse)
4. Double-Ended Bit
5. Magnetic Tray
6. Battery Pack (not included)
7. Latches
8. Depress Latched To Release Battery Pack
9. Torque Adjusting Ring
10. To Decrease Torque
11. To Increase Torque
12. Reverse
13. Forward
14. Unlock (Release)
15. Lock (Tighen)
16. Chuck Jaws
17. High Speed
18. Low Speed
19. Two-Speed Gear Switch
20. Bit Storage
21. Drill Bit
SPECIFICATIONS
Voltage
Chuck
Switch
No load speed (drill mode):
- Lo speed
- Hi speed
Clutch
Max. Torque
Max. Spade Bit
Weight - not incl.battery pack
1
HU RO LV LT EE HR SI SK GR TR
14.4 V
2-13 mm
Variable speed
0 - 440 min -
1
0 - 1600 min -
1
24 Positions
37.5 Nm
19 mm
1.22 Kg