Publicité
Les langues disponibles
Les langues disponibles
Small debris or loose pieces of wood or other objects
that contact the revolving blade can be thrown with high
speed.
Cut only one workpiece at a time. Stacked multiple
workpieces cannot be adequately clamped or braced
and may bind on the blade or shift during cutting.
Ensure the mitre saw is mounted or placed on a
level, firm work surface before use. A level and
firm work surface reduces the risk of the mitre saw
becoming unstable.
Plan your work. Every time you change the bevel or
mitre angle setting, make sure the adjustable fence
is set correctly to support the workpiece and will
not interfere with the blade or the guarding system.
Without turning the tool "ON" and with no workpiece
on the table, move the saw blade through a complete
simulated cut to assure there will be no interference or
danger of cutting the fence.
Provide adequate support such as table extensions,
saw horses, etc. for a workpiece that is wider or
longer than the table top. Workpieces longer or
wider than the mitre saw table can tip if not securely
supported. If the cut-off piece or workpiece tips, it can
lift the lower guard or be thrown by the spinning blade.
Do not use another person as a substitute for a
table extension or as additional support. Unstable
support for the workpiece can cause the blade to bind
or the workpiece to shift during the cutting operation
pulling you and the helper into the spinning blade.
The cut-off piece must not be jammed or pressed
by any means against the spinning saw blade. If
confined, i.e. using length stops, the cut-off piece could
get wedged against the blade and thrown violently.
Always use a clamp or a fixture designed to
properly support round material such as rods or
tubing. Rods have a tendency to roll while being cut,
causing the blade to "bite" and pull the work with your
hand into the blade.
Let the blade reach full speed before contacting the
workpiece. This will reduce the risk of the workpiece
being thrown.
If the workpiece or blade becomes jammed, turn the
mitre saw off. Wait for all moving parts to stop and
disconnect the plug from the power source and/
or remove the battery pack. Then work to free the
jammed material. Continued sawing with a jammed
workpiece could cause loss of control or damage to the
mitre saw.
After finishing the cut, release the switch, hold the
saw head down and wait for the blade to stop before
removing the cut-off piece. Reaching with your hand
near the coasting blade is dangerous.
Hold the handle firmly when making an incomplete
cut or when releasing the switch before the saw
head is completely in the down position. The
braking action of the saw may cause the saw head to
be suddenly pulled downward, causing a risk of injury.
SAFETY INSTRUCTIONS FOR WOOD CUTTING
BLADE
Please read the manual and instructions carefully
before using the saw blade and the machine.
The product must be in good condition, the spindle
without deformation and vibration.
Do not use the product without the guards in position.
Keep guards in good working order and properly
maintained.
Ensure the operator is adequately trained in safety
precautions, adjustment and operation of the product.
Always wear goggles and ear protection when using the
product. It is recommended to wear gloves, sturdy non
slipping shoes and apron.
Before using any accessory, consult the instruction
manual. The improper use of an accessory can cause
damage and increase the potential for injury.
Use only blades specified in this manual, complying
with EN 847-1.
blade. Ensure the speed marked on the saw blade is at
least equal to the speed marked on the saw.
Always use blades with correct size and shape of
arbour holes. Blades that do not match the mounting
hardware of the saw will run eccentrically, causing loss
of control.
Do not use blades of larger or smaller diameter than
recommended. Do not use any spacers to make the
blade fit onto the spindle.
Check the tips of the saw blade for damage or abnormal
appearance before each use. Tips that are damaged or
loose can become flying objects in use and increase the
chance of personal injury.
Do not use cracked or distorted saw blades. Do not use
saw blades that are damaged or deformed.
Scrap the saw blade if damaged, deformed, distorted or
cracked, repairing is not permitted.
Do not use HSS blades.
Ensure the saw blade is mounted correctly, tighten the
8-10 Nm).
Fastening screw and nuts shall be tightened using the
appropriate spanner, etc.
blows is not permitted.
Make sure the blade and flanges are clean and the
recessed sides of the collar are against the blade.
Make sure the blade rotates in the correct direction.
Before work, make a dummy cut without the motor
turned on so the position of the blade, operation of
the guards with respect to other machine parts and
workpiece may be checked.
Never leave the product unattended.
Do not apply lubricants on the blade when it is running.
Never perform any cleaning or maintenance work when
the machine is still running and the head is not in the
rest position.
Never attempt to stop a machine in motion rapidly
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
English |
3
Publicité
